AirMan SDG25S-8E1 Скачать руководство пользователя страница 51

Страница: 51 / 81

6. Periodic Inspection/Maintenance

6.5 Maintenance

6.5.1 Change engine oil

[At 50 hours for the first change and every 250 hours thereafter]

CAUTION

-----1

Caution in filling or draining engine oil

• When checking, replenishing, and draining the engine oil, be sure

to wait 10 to 20 minutes after engine stops until it cools down.

• Engine oil is very hot and highly pressurized during or just after

the operation. Hot oil could blow out and can cause injury.

• Never supply more engine oil than the proper level. Too much oil

could cause white smoke out of the exhaust, and it can cause
damage and accident to engine.

CD Remove the drain plug "1'' attached outside the

plane, open a drain valve "2" inside the plane, and
discharge engine oil drain.

® When the oil is completely drained, close a drain

valve after attaching a drain plug , remove the cap

of an engine oil filler port "3" , refill new engine oil.

[Oil supply: about 2.6gal. (1

OL)]

@ After finishing the oil supply, tighten the cap of oil

filter port firmly.

normal oil supply with an oil level gauge before
operating this machine.

6-5

H990432

1 2

Figure SDG25S-8E1

A130902

BTW Equipment Supply LLC dba Airman Arizona • www.btwequipmentsupply.com www.airmanarizona.com

SDG45S-8E1

Instruction Manual

ORDER PARTS ONLINE

www.airmanarizona.com

Содержание SDG25S-8E1


















































































Результаты поиска

Содержание SDG25S-8E1

Отзывы:

Бренды по названию

Популярные бренды

AirMan SDG25S-8E1, Инструкция по эксплуатации

Результаты поиска

Содержание SDG25S-8E1

Отзывы:

Бренды по названию

Популярные бренды