AirLive PoE-2600HD Скачать руководство пользователя страница 12

Страница: 12 / 112

1. Introduction

AirLive PoE-2600HD/
WN-2600HD User’s Manual

1. Insert the paper clip or other tool and press and hold the button down continuously.

2. Hold it at least 5 seconds and release the tool. Then the device has been restored

to default settings and reboot again.

Note

: Restoring the factory default setting will lose the all previous settings included

IP address forever. User needs to run the IPWizard II program to search the device

and configure it to let the device work properly again.

LAN Socket

The LAN socket is a RJ-45 connector for connections to 10Base-T Ethernet or

100Base-TX Fast Ethernet cabling. This Ethernet port built N-Way protocol can detect or

negotiate the transmission speed of the network automatically. Please use Category 5

cable to connect the Network Camera to a 100Mbps Fast Ethernet network switch or hub.

LAN LED (green color)

This LED will be flashing while network accessing via Ethernet.

Power / Wireless LED (orange color)

This LED is used to indicate whether DC power is on or not. In addition, this LED will be

flashing while the wireless accessing of the Camera.

DI/DO Connector

The Camera provides a terminal block with 4 pins of connectors for DI and DO. Please

refer to the Appendix A in this manual for more information. The pin 1 is located at the right

side of terminal block from rear view.

Micro SD Card Slot

User can insert a micro SD card into this slot for event recording.

Содержание PoE-2600HD

















































































































Результаты поиска

Содержание PoE-2600HD

Отзывы:

Похожие инструкции для PoE-2600HD

Бренды по названию

Популярные бренды

AirLive PoE-2600HD, Руководство пользователя

Результаты поиска

Содержание PoE-2600HD

Отзывы:

Похожие инструкции для PoE-2600HD

Бренды по названию

Популярные бренды