AIRLESSCO GS950 Скачать руководство пользователя страница 26

Страница: 26 / 36

Pinion Assembly/Clutch Armature/Clamp

3A4108F

Clutch Armature

Use an impact wrench or wedge

something between clutch armature (25)

and clutch housing to hold engine shaft

during removal.

Remove four screws (23) and lock

washers (24).

10. Remove armature.

Installation

Clutch Armature

Lay two stacks of two dimes on smooth

bench surface.

Lay armature (25) on two stacks of

dimes.

Press center of hub (26) down to bench

surface.

Install armature (25) on engine drive

shaft.

Install four screws (23) and lock washers

(24) with torque of 125 in-lb.

Pinion Assembly

Check o-ring (29d) and replace if

missing or damaged.

Tap pinion shaft (29a) in with plastic

mallet.

Install retaining ring (29b) with beveled

side facing up.

Place pinion assembly on bench with

rotor side up.

Apply thread sealant to screws. Install

four screws (28) and lock washers (24).

Alternately torque screws to 125 in-lb

until rotor is secure. Use threaded holes

to hold rotor.

Install pinion assembly (29) with four

screws (36) and washers (37).

Connect clutch cable connectors to

inside of pressure control.

TIA

0.12+01 in (3.0+.25 mm)

dimes

ti6321a

Содержание GS950





































Результаты поиска

Содержание GS950

Отзывы:

Похожие инструкции для GS950

Бренды по названию

Популярные бренды

AIRLESSCO GS950, Операция - Ремонт - Запчасти

Результаты поиска

Содержание GS950

Отзывы:

Похожие инструкции для GS950

Бренды по названию

Популярные бренды