the Boiler cap is removed.
Steam cleaning
NOTE: Before operating, make sure all desired accessories are connected and Boiler is
fi
lled with the
correct amount of water.
1.
For first
-time use, remove
protective plastic cover that is shipped on electrical plug. Plug
power
cord into a convenient 3-prong electrical outlet. Heating Indicator Light will illuminate to show
that unit is receiving power and Boiler has started to heat.
CAUTION: This unit uses a grounded (3-prong) electrical plug. Use only in properly installed
3-prong electrical outlets. Do not attempt to alter plug or circumvent this safety feature in any
way.
2. After approximately 3 minutes, Heating Indicator Light will turn off. This indicates that Boiler is
fully heated, and unit is ready to begin steaming.
NOTE: Heating Indicator Light may cycle off and on during use, accompanied by a slight
temporary drop in steam pressure – this is a normal part of operation, as the Boiler works to
maintain a steady optimal temperature.
3.
Point Jet Nozzle (and any connected accessories) towards surface you wish to steam, and
press
Steam Trigger.
Hold Trigger down for a continuous flow of steam.
CAUTION: Always be sure that Jet Nozzle and other accessories are pointed in a safe direction
(away from yourself, other people, pets, and plants) before pressing Steam Trigger.
NOTE: When steaming any surface for the first time, it is recommended that you consult
the
manufacturer’s guidelines for material being steamed. For items in question, test steam on an
inconspicuous area before proceeding.
4. Using a slight back-and-forth motion over the area you are steaming will enhance the cleaning
process, as will scrubbing the area (if a Brush is connected). Wipe steamed areas with a clean
cloth to remove loosened dirt and grime.
CAUTION: Wiping an area while it is still wet is recommended, but use care when wiping surfaces
such as metal that may still be hot.
5. To effectively kill bacteria and other microorganisms, hold Jet Nozzle (and any connected
accessories) approximately 1/2 inch from surface and press Steam Trigger. Keep Trigger pressed
and concentrate steam on the same spot for at least 5 seconds.
6. At its maximum capacity (6 oz. / 180 ml.), the Boiler will provide approximately 8 minutes of
continuous steam. If you wish to continue steaming, refer to FILLING BOILER procedure. Be sure to
note
Refilling Boiler
section at bottom of page.
7.
Once you are finished using your
Hand Held Steamer, immediately unplug power cord from
electrical outlet. Refer to Storage & Care guidelines for proper cleaning and storage procedures.
Proper storage
Preparing your
Hand Held Steamer
for storage is quick and simple. When you have finished
your
steaming tasks, follow the steps listed below.
1. Unplug power cord from electrical outlet.
2. Allow unit to cool (30 minutes for complete cooling).
3.
Press and hold Steam Trigger to release all remaining steam pressure.
4. Unscrew and remove Boiler Cap. Drain all remaining water from Boiler into a sink or tub, then
loosely replace Boiler Cap.
NOTE: Do not overtighten Boiler Cap when storing, as this may make it difficult to remove
during
next use.
5. Loosely bundle power cord, and store your unit in a cool dry location.
Care and maintenance
A common maintenance need for steam appliances is the removal of build-up caused by mineral
content in water. This mineral build-up may limit the effectiveness and reduce the life of your
steamer.
The best way to minimize mineral build-up is to use distilled or de-mineralized water when using
your steamer. If you are unable to use distilled water, it is recommended that the following
procedure be followed monthly to help remove any mineral build-up:
1. Unplug power cord from electrical outlet.
2. Allow unit to cool (30 minutes for complete cooling).
3.
Press and hold Steam Trigger to release all remaining steam pressure.
4. Unscrew Boiler Cap and drain all remaining water from Boiler into a sink or tub.
5. Unscrew and remove Boiler Cap, and drain any remaining water from Boiler into a sink or tub.
6. Fill Measuring Cup with 6 oz. (180 ml.) distilled vinegar. Carefully pour vinegar into Boiler.
7. Slowly shake or move unit around to agitate vinegar.
