Airetool ATP III Скачать руководство пользователя страница 13

Страница: 13 / 20

Page 13

PL19-6000EN

05/15/2015

I. Local Menu:

This screen allows the operator to toggle the LOCAL

mode ON or OFF, default is OFF. With LOCAL mode

ON, the shroud buttons replace the pendant control

buttons as the method to operate the pump.

NOTE: The word LOCAL replaces OK on the Normal

Operations display and the pendant control buttons

become deactivated.

LOCAL mode will provide operation of the pump if the

pendant control or pendant control cable is damaged.

Toggle LOCAL mode ON or OFF by pressing the Down

or Up Arrow buttons. Save the setting and step forward

by pressing the Menu button.

J. Language Menu:

With a language shown on the text display the operator

can change the display language by pressing the Down

or Up Arrow buttons. Save the setting and step forward

by pressing the Menu button.

K. Diagnose Menu:

This screen allows the operator to trouble shoot several

pendant problems by displaying if the microprocessor

has received a signal from the pendant control button.

No signal indicates the problem is most likely with the

pendant keypad or pendant cord. Use LOCAL mode to

operate the pump until the problem can be corrected.

Airetool

General Instructions

Figure 22: Local Menu

Figure 23: Language Menu

Figure 24: Diagnose Menu

not used

Fan

Pendant Down Arrow button

Pendant Up Arrow button

Pendant ON / OFF button

Figure 25: Diagnose Menu

ON / OFF (Motor)

button pushed

Up Arrow (Advance)

button pushed

Содержание ATP III





















Результаты поиска

Содержание ATP III

Отзывы:

Бренды по названию

Популярные бренды

Airetool ATP III, Инструкция по эксплуатации

Результаты поиска

Содержание ATP III

Отзывы:

Бренды по названию

Популярные бренды