PAGE: 7/8
Fig.17
1. Remove battery cover, install the battery (12V, not
included) to the transmitter.
2. Sliding the switch to the position of "CFL" when using
CFL bulbs. (Do not use fixture on dimming switch
when using CFL bulbs.)
3. Workable for dimming switch when using max. 40-watt
incandescent bulbs, please sliding the switch to the
position of "D"
4. Set the code:
within the 30 seconds time frame after the main power
is turned on, operate either process of the following.
remove the battery cover on transmitter and insert
batteries. remove the existing batteries and place it
again.
press and hold "HI" and "LOW" button for 5 seconds.
the LED indicator of transmitter began to flash.
once set Code successful, the fan at low speed, the
light was turn off.
5. OPERATING TRANSMITTER:
* Press "HI" to turn on the fan at high speed.
* Press "MED" button to turn the fan in medium speed.
* Press "LOW" button to turn the fan in low speed.
* Press "OFF" button to turn off the fan.
* Press and hold the "OFF" button over 5 seconds, the
light will turn off within 1minute.
* Press and release the " " button quickly to turn on or
turn off the light.
* Press and hold the " " button to
dim or brighten lights
to the desired level and release, and the brightness level
will be memorized. Turn on the light again, then fan light
will restore on of the brightness level which was dimmed
last time.
OFF
HI
LOW
MED
ＨＩ
ＭＥＤ
ＬＯＷ
ＯＦＦ
Ｄ
ＣＦＬ
１２Ｖ
ＦＣＣ ＩＤ： Ａ２５－ＴＸ００５Ｒ
Ｔｈｉｓ ｄｅｖｉｃｅ．．．．．．．．．．．．．．．．．．．．．．．
．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．
．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．
．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．
．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．
．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．
．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．
．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．
．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．
．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．
．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．
．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．
．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．
．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．
Ｄ
ＣＦＬ
Battery Cover
Transmitter
Switch
To access the inner light bulbs, remove
2 screws from the light plate and carefully
pull upwards. Replace the defective bulbs
with a similar Max.40W bulbs.
Replace the light plate and bulb into the
housing, and secure with 2 screws.
Fig.15
Fig.16
Note:
This remote controller has memory function setting. The fan will
operate at the same speed and the fan light will stay at the same
brightness as the last time the power supply was turned off.
Replace the Inner Light Bulbs
WARNING:
This fan light has a built-in current limiting device to conserve energy. The fan light will not operate
if the combined wattage of the installed bulbs exceeds 300 Watts. The fan light will proper
functioning if the combined wattage of the installed bulbs less than 300 Watts, but the output
power limit under 190 W.
F A N C O
140819
