Aire-Flo 92AF1DF Скачать руководство пользователя страница 12

Страница: 12 / 48

Page 12

TABLE 2

COMBUSTIBLE FLOORING BASE OPENING SIZE

Cabinet

Width

Catalog

Number

Front to Rear

Side to Side

in.

B Cabinet

(17.5")

11M60

559

18 − 3/4

476

C Cabinet

(21")

11M61

559

22 − 3/4

578

FIGURE 13

FURNACE

SUPPLY AIR

PLENUM

COMBUSTIBLE

FLOORING BASE

PROPERLY

SIZED FLOOR

OPENING

2 − After opening is cut, set the combustible flooring base

into opening.

3 − Check fiberglass strips on the combustible flooring

base to make sure they are properly glued and posi-
tioned.

4 − Lower supply air plenum into the combustible flooring

base until plenum flanges seal against fiberglass
strips.

NOTE

− Be careful not to damage fiberglass strips.

Check for a tight seal.

5 − Set the furnace over the plenum.

6 − Ensure that the seal between the furnace and plenum

is adequate.

Installation on Cooling Coil Cabinet (Figure 14)

NOTE

− Downflow combustible flooring kit is not used..

1 − Refer to reverse−flow coil installation instructions for

correctly sized opening in floor and installation of cabi-
net.

2 − When cooling cabinet is in place, set and secure the

furnace according to the instructions that are provided
with the cooling coil. Secure the furnace to the cabinet.

3 − Seal the cabinet and check for air leaks.

FIGURE 14

COOLING COIL

PLENUM

PROPERLY

SIZED FLOOR

OPENING

FURNACE

Return Air Opening −− Counterflow Units

Return air may be brought in only through the top opening
of a furnace installed in the counterflow position. The fol-
lowing steps should be taken when installing plenum:

1 − Bottom edge of plenum should be flanged with a

hemmed edge (See figure 15 or 16).

2 − Sealing strips should be used to ensure an airtight seal

between the cabinet and the plenum.

3 − In all cases, plenum should be secured to top of fur-

nace using sheet metal screws.

4 − Make certain that an adequate seal is made.

ÉÉÉÉ

FIGURE 15

SECURE FROM

OUTSIDE CABINET

PLENUM

(Field Provided)

SEALING STRIP

(Field Provided)

Side View

CABINET

SIDE PANEL

ÉÉÉÉ

SECURE FROM

INSIDE CABINET

PLENUM

(Field Provided)

SEALING STRIP

(Field Provided)

Side View

CABINET

SIDE PANEL

FIGURE 16

Содержание 92AF1DF

















































Результаты поиска

Содержание 92AF1DF

Отзывы:

Похожие инструкции для 92AF1DF

Бренды по названию

Популярные бренды

Aire-Flo 92AF1DF, Руководство по установке

Результаты поиска

Содержание 92AF1DF

Отзывы:

Похожие инструкции для 92AF1DF

Бренды по названию

Популярные бренды