Aire-Flo 92AF1DF Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 48

background image

Page 28

FIGURE 40

12" (305mm)

ABOVE GRADE OR

AVERAGE SNOW

ACCUMULATION

UNCONDITIONED

SPACE

1/2" (13mm) FOAM

INSULATION

1/2" (13mm) FOAM

INSULATION IN

UNCONDITIONED

SPACE

*WALL SUPPORT

OUTSIDE WALL

SIZE TER-
MINATION

PIPE PER

TABLE 8.

FIELD−PROVIDED

REDUCER MAY BE

REQUIRED TO

ADAPT LARGER

VENT PIPE SIZE TO

TERMINATION

*Use wall support every 24" (610). Use

two supports if extension is greater

than 24" but less than 48".

12" (305mm) MAX. for 2" (51mm)
20" (508mm) MAX. for 3" (76mm)

NON−DIRECT VENT FIELD SUPPLIED WALL TERMINATION EX-

TENDED OR (15F74) WALL TERMINATION VENT PIPE EXTENDED

6" (152mm)

Max

NOTE − Do not discharge exhaust gases directly into any chimney or vent stack. If ver-
tical discharge through an existing unused chimney or stack is required, insert piping
inside chimney until the pipe open end is above top of chimney and terminate as illus-
trated. In any exterior portion of chimney, the exhaust vent must be insulated.

FIGURE 41

3" − 8"

(76mm−

203mm)

3" − 8"

(76mm−

203mm)

STRAIGHT−CUT OR

ANGLE−CUT IN DIRECTION

OF ROOF SLOPE

EXHAUST VENT

1/2" (13mm)

WEATHERPROOF

INSULATION

SHOULDER OF FITTINGS

PROVIDE SUPPORT

OF PIPE ON TOP PLATE

EXTERIOR

PORTION OF

CHIMNEY

INSULATE

TO FORM

SEAL

SHEET

METAL TOP

PLATE

SIZE TERMINATION

PIPE PER TABLE 8.

92AF1DF/95AF1DF NON−DIRECT VENT

APPLICATION USING EXISTING CHIMNEY

Minimum 12" (305MM)

above chimney top

plate or average snow

accumulation

Condensate Piping

This unit is designed for either right- or left-side exit of con-
densate piping. Refer to figure 42 for condensate trap loca-
tions.

NOTE

− If necessary the condensate trap may be installed

up to 5´ away from the furnace. Use PVC pipe to connect
trap to furnace condensate outlet. Piping from furnace
must slope down a minimum of 1/4" per ft. toward trap.

FIGURE 42

CONDENSATE TRAP AND PLUG LOCATIONS

Trap

(same on

right side)

Plug

(same on left

side)

1−1/2 in.

1 − Determine which side condensate piping will exit the

unit, location of trap, field−provided fittings and length of
PVC pipe required to reach available drain.

2 − Remove plug (figure 42) from the cold end header box

at the appropriate location on the side of the unit. Install
field−provided 1/2" NPT male fitting into cold end head-
er box. Use teflon tape or appropriate pipe dope.

3 − Install the cap over the clean out opening at the base of

the trap. See figure 45.

NOTE

− Vinyl tubing may be used for condensate drain.

Tubing must be 1−1/4" OD X 1" ID and should be attached to
the drain on the trap using a hose clamp.

4 − Install drain trap using appropriate PVC fittings, glue

all joints. Glue the provided drain trap as shown in fig-
ure 45. Route the condensate line to an open drain.

NOTE

− If necessary the condensate trap may be installed

up to 5 feet away from the furnace. Piping from furnace
must slope down a minimum of 1/4" per ft. toward trap.

«
...
26
27
28
29
30
...
»

Содержание 92AF1DF

















































Отзывы:

Нет отзывов

Похожие инструкции для 92AF1DF

Бренд: Bard Страницы: 67

Бренд: Fedders Страницы: 4

Airco HTL Series

Бренд: Olsen Страницы: 32

Бренд: Payne Страницы: 22

Shaker Grate Series

Бренд: Cozeburn Страницы: 2

Бренд: Carrier Страницы: 50

Бренд: UPG Страницы: 16

Бренд: Johnson Страницы: 20

Бренд: Unitary products group Страницы: 28

Бренд: Amana Страницы: 10

Бренд: York Страницы: 12

Empyre Elite 100

Бренд: Pro-Fab Industries Страницы: 32

Empyre Elite XT

Бренд: Pro-Fab Industries Страницы: 32

Бренд: Nortek Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды