Air Live G.DUO Скачать руководство пользователя страница 119

Страница: 119 / 137

12. Frequent Asked Questions

AirLive G.DUO User’s Manual

112

Question

Why can’t I get SNMP access?

Answer

: The SNMP management interface is turned off by default. Please go to

“System Configuration-> SNMP Management” menu to enable it.

====================================================================

Question

Where is the POE port for G.DUO?

Answer

: The PoE system used for G.DUO is 12V Passive PoE. LAN1 is also used as

the passive PoE port.

====================================================================

Question

Where is the signal survey function that displays the signal strength

continuously for antenna alignment?

Answer

: The “Signal Survey” function is inside the Site Survey function. After the site

survey, please select a SSID and press the “Signal Survey” button.

The

signal strength is indicated by percentage, not by SIGNAL STRENGTH

The higher the number, the stronger the signal.

====================================================================

Question

Why can’t I perform emergency upgrade correctly?

Answer

: 1. Please make sure you are connecting your PC to LAN2, LAN3, or LAN4.

Do not connect to LAN 1.

2. You need special firmware for emergency upgrade. Please visit

www.airlive.com

to download the file.

Содержание G.DUO










































































































































Результаты поиска

Содержание G.DUO

Отзывы:

Air Live G.DUO, Руководство пользователя, Страница: 119 / 137

Результаты поиска

Содержание G.DUO

Отзывы: