Air Live G.DUO Скачать руководство пользователя страница 115

Страница: 115 / 137

11. Emergency Firmware Recovery

AirLive G.DUO User’s Manual

108

The G.DUO features emergency firmware upgrade function that can restore your AP from a

firmware crashed. If you can’t access your AP anymore, please first try to restore the

setting to default by holding the RESET button (in the back) for more than 7 seconds. You

should be able to find the AP at 192.168.1.254. If you can’t find it, then please perform the

emergency upgrade.

The Emergency Upgrade requires special G.DUO firmware

please visit www.airlive.com->support->download and type “G.DUO” to the download page.

How Emergency Upgrade Works?

G.DUO’s flash memory is divided into “firmware” and “bootloader” area. The bootloader

area is protected from writing and has a built-in emergency web server. Therefore, the AP

can be recovered from emergency web server after a firmware crash. The emergency

web server is enabled when AP is forced into emergency upgrade mode, it’s IP will be

changed to

192.168.1.6

Procedure to Restore the AP using Emergency Upgrade

1. Please connect your PC directly to the

LAN 2, LAN3, or LAN4 port

of the AP. Do not

connect to LAN1.

2. set your PC’s IP address to 192.168.1.50

3. Before connecting the power, please press and holding the “Reset” button(in the back of

the AP). Then plug in the power. Keep press and hold the Reset button until the

“Power” LED goes off(about10 seconds)

11.

Emergency Firmware

Recovery

Bootloader Area

Flash Memory

Emergency

Web Server

Firmware Area

Содержание G.DUO










































































































































Результаты поиска

Содержание G.DUO

Отзывы:

Air Live G.DUO, Руководство пользователя, Страница: 115 / 137

Результаты поиска

Содержание G.DUO

Отзывы: