Air Live G.DUO Скачать руководство пользователя страница 110

Страница: 110 / 137

9. System Configuration Menu

103

AirLive G.DUO User’s Manual

Upgrade Firmware:

To update the G.DUO firmware, first download the firmware from AirLive web site to

your local disk.

Please do not use the firmware for Emergency Upgrade, it might

damage your AP!.

Then from the above screen enter the path and filename of the

firmware file (or click

Browse

to locate the firmware file). Next, Click the

Upgrade

button to start.
The new firmware will be loaded to your G.DUO. After a message appears telling you

that the operation is completed, you need to reset the system to have the new firmware

take effect.

Do not power off the device while upgrading the firmware.

It is recommended that you do not upgrade your G.DUO unless the

new firmware has new features you need or if it has a fix to a problem

that you’ve encountered.

9.7.2 Configuration Save and Restore

System Configuration -> Configuration Save and Restore

The G.DUO can save and restore the settings to a file. In addition, it has the unique

capability to restore only the network or wireless settings. This makes changes of wireless

settings across the entire network of AP much easier.

You can save system configuration settings to a file, and later download it back to the

G.DUO by following the steps.

Step 1

Select

Configuration Save and Restore

from the

System Configurations

menu.

Содержание G.DUO










































































































































Результаты поиска

Содержание G.DUO

Отзывы:

Air Live G.DUO, Руководство пользователя, Страница: 110 / 137

Результаты поиска

Содержание G.DUO

Отзывы: