background image

HEPA Filters (High Efficiency Particle Arrestors) 

This type of filter is generally fitted in front withdrawal frame. Filters will be held into the 
frame by retaining bars which can be removed to allow access to replace filters. 

Carbon Filters 

Carbon filters normally have an active life of about twelve (12) months, or more. It is 
advisable to remove a sample from the pack to return to manufacturer to determine the 
remaining working life, preferably after the first six (6) months & subsequent six (6) monthly 
intervals. 
 
NOTE! WHEN REPLACING ALL FILTERS ENSURE FILTER IS FACING CORRECT 
DIRECTION AS INDICATED BY AN AIRFLOW ARROW.  
 

ROUTINE MAINTENANCE SCHEDULE 

 

 

 

 

 
 

Monthly 

3 Monthly 

6 Monthly 

Annually 

Fan Shaft Bearings 

 

 

 

 

Motors 

 

 

 

 

Belts & Pulleys 

 

 

 

 

Elec. Heater Battery 

 

 

 

 

Coils 

 

 

 

 

Eliminators 

 

 

 

 

Dampers 

 

 

 

 

Panel & Bag Filters 

 

 

 

 

HEPA Filters 

 

 

 

 

Carbon Filters 

 

 

 

 

External Surfaces 

 

 

 

 

 

MAINTENANCE OF UNITS CONTAINING F GAS REFRIGERANTS. 
 

It is a legal requirement that all units containing F Gas refrigerants such as R407c, R410a are 
serviced on a regular basis and that leak tests are carried out. This should generally be carried 
out at least every six months and a service inspection sheet issued to the customer upon 
completion. Log books should be kept on site by the end user to prove that these works have 
been carried out. The responsibility of compliance is shared by the end user and the appointed 
maintenance engineers. 
 
Failure to comply with the F Gas regulations will result in invalidation of the warranty on the 
refrigeration system within the unit. 
 

INVALIDATION OF GUARANTEE 

 

 

 

 

 

 

The following misuses or maltreatment of AIR HANDLERS LIMITED equipment will 
render all guarantees, as set out on the Conditions of Sale, void. 
 

 

Failure to install, set up or put to work any part of the equipment as specified in AIR 
HANDLERS LIMITED Installation, Operation and Maintenance Instructions. 

 

Attempting to operate the motors and other electrical equipment with an electrical 
supply other than that designated on the motor nameplate, or failing to connect and 
protect such equipment in accordance with I.E.E. Regulations and local by-laws. 

 

Failure to notify AIR HANDLERS LIMITED of equipment damaged on receipt in 
writing within five (5) days. 

 

Failure to run equipment within the design specifications as notified at the time of 
order. 

Содержание Envirofresh Series



















Отзывы: