Aim-TTI TGR2050 Series Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 100

Aim-TTI TGR2050 Series Скачать руководство пользователя страница 6

1 - Safety

Safety notices

5

TGR2050 Series Instruction Manual

Safety notices

This instrument is:

·

A safety Class I instrument according to IEC classification and has been designed

to meet the requirements of EN61010-1 (Safety Requirements for Electrical

Equipment for Measurement, Control and Laboratory Use).

·

An Installation Category II instrument intended for operation from a normal

single-phase supply.

·

Tested in accordance with EN61010-1 and has been supplied in a safe condition.

·

Designed for indoor use in a Pollution Degree 2 environment in the temperature

range 5°C to 40°C, 20% - 80% RH (non-condensing).

WARNING

Do not operate while condensation is present.
Do not operate outside its rated supply voltages or environmental range.

THIS INSTRUMENT MUST BE EARTHED.

Any interruption of the mains earth connector, inside or outside, will make the

instrument dangerous. Intentional interruption is prohibited.
Any adjustment, maintenance and repair of the opened instrument under voltage

must be avoided.

When connected, terminals may be live and opening the covers or removal of parts

(except those that can be accessed by hand) may expose live parts.
To avoid electric shock, or damage to the instrument, never allow water to get inside

the case.

If the instrument is clearly defective, has been subject to mechanical damage,

excessive moisture or chemical corrosion the safety protection may be impaired and

it must be withdrawn from use and returned for repair.
This instrument is protected by an internal fuse which is not user serviceable.
This instrument uses a Lithium button cell for non-volatile memory battery back-up;

typical life is 5 years. In the event of replacement becoming necessary, replace only

with a cell of the correct type, i.e. 3V Li/Mn0

2

20mm button cell type 2032.

Exhausted cells must be disposed of carefully in accordance with local regulations;

do not cut open, incinerate, expose to temperatures above 60°C or attempt to

recharge. Refer to ‘TGR2050 Service Guide’ for further details.

CAUTION

Do not wet when cleaning, use only a soft dry cloth to clean the screen.

«
...
4
5
6
7
8
...
»

Содержание TGR2050 Series





































































































Отзывы:

Нет отзывов