AIM Joraco TOCCLE-AIRE HP-16 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 26

background image

HYDRO-PNEUMATIC SERIES PRESSES

OVERVIEW, INSTALLATION, AND OPERATION

1

Section I: Press Overview

1.1 Description

The Hydro-Pneumatic (HP) Series Press is a completely self-contained, air-over-oil unit that
is cost-effective and can be used in a variety of assembly and forming applications including
punching, marking, staking, cutting, crimping and flaring. Our HP presses are available in

sizes from 2 to 16 tons and the standard specifications are: 4” stroke with up to ½” power
stroke, 8” open height, 20” between columns and an 8” x 10” pre

cision ground bolster plate.

Our HP Series Presses cut down on air consumption but still deliver the maximum force
required for your application.

1.2 Features

•

Self-contained

•

Clean

•

Quiet

•

Adaptable

•

No springs

•

Only 3 moving components

•

No external hydraulics

1.3 Options

•

EZ-Dial Force Regulator

•

Adjustable Output

•

Filter, Regulator, Lubricator (FRL)

–

clean room compliance

•

Dwell Timer

•

Non-Rotating Ram

•

Can be PLC ready for automated setups and force monitoring packages

*** Custom Features may be quoted upon request
*** C-Frame option also available upon request

*** HP Series Cylinders also sold separately

«
...
2
3
4
5
6
...
»

Содержание TOCCLE-AIRE HP-16



























Отзывы:

Нет отзывов

Похожие инструкции для TOCCLE-AIRE HP-16

Бренд: Gearwrench Страницы: 3

Бренд: MULTIQUIP Страницы: 60

Бренд: SW-Stahl Страницы: 12

HURST eDRAULIC SC 258 E2

Бренд: Idex Страницы: 44

Бренд: Xinpu Страницы: 12

Central Pneumatic 1/4" Stubby Air Ratchet 91002

Бренд: Central Pneumatic Страницы: 8

PSI 9000 WR 3U SLAVE

Бренд: Elektro-Automatik Страницы: 44

Бренд: OMERA Страницы: 50

Бренд: BorMann Страницы: 4

Бренд: Yokota Страницы: 8

Бренд: Rikon Power Tools Страницы: 40

Muyang SZLH Series

Бренд: Famsun Страницы: 46

MX-7-420 TURBO-PROP

Бренд: MAULE Страницы: 40

Бренд: Daiwa Страницы: 5

Бренд: Brunton Страницы: 2

Бренд: Lumina Power Страницы: 19

Бренд: CGOLDENWALL Страницы: 24

Бренд: Black Ridge Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды