Ahlborn ALMEMO 2290-4 V5 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 48

Ahlborn ALMEMO 2290-4 V5 Скачать руководство пользователя страница 28

The sensor is then brought to a defined nominal value (boiling water, known
weight etc.) and the nominal value is entered. For this purpose the key

must twice be pressed long (approx. 1 sec.) until the first digit of the

▲

PROGR

measured value flashes. Then, by entering the nominal value (see 5.4), the
scaling value is calculated, stored as FACTOR and the measured value is
indicated accordingly.

The functions base value ´

BA

´ and factor ´

FA

´ must be activated

and released! (see 6.7)

6.7 Locking the Programming of the Sensor

(s.man. 6.3.12)

The function parameters of each measuring point are protected by the locking
mode up to an adjustable locking level. Before any programming is performed
the locking mode must be correspondingly lowered. If a dot is indicated
following the locking mode on the display then a modification is not possible.

Locking Level

Locked Functions

0

none

1

measuring range + element flags

2

measuring range + zero point and slope correction

3

measuring range + dimension

4

+ zero point and slope correction

5

+ base value, factor, exponent

6

+ analogue output, start and end

7

+ limit values, max and min

Function LOCKING MODE ´

LM

´

Selection with key

F2...

...

Input see 5.4

F2

1:0 0 0 5

LM

If programmed, the output function, element flags and multiplexer setting will be
indicated next to the locking mode (see man. 6.10.2/3/4).

28

ALMEMO



2290-4

Sensor Programming

«
...
26
27
28
29
30
...
»

Содержание ALMEMO 2290-4 V5

















































Отзывы:

Нет отзывов