Ahlborn ALMEMO 2290-2/3 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 44

background image

Tips regarding correct handling of batteries:

Do not leave used batteries in the instrument!

Remove batteries from the instrument if it is not used for a long period.

Risk to health and instrument failure can result from leaking batteries!

Therefore, only use leak-proof batteries.

Used batteries are hazardous waste and must be disposed in an

environmentally friendly way! Return them to the dealer or dispose of
them in a battery storage container.

Operation with Rechargeable Batteries

Rechargeable batteries can be used instead of normal batteries. Due to their
smaller capacity of 110mAh they only reach an operating time of 16 hours. The
operating time will be shortened if sensors or modules are connected that
consume additional current. It is recommended to use the 9V rechargeable
battery with plug-integrated charger unit ZB 2000 LS, which is included in the
range of accessories.
Tips regarding correct handling of rechargeable batteries:

The rechargeable batteries supplied are not charged when delivered!
If NiCD cells are only partly discharged, the full capacity cannot be

reached by a normal recharging.

Therefore, use the instrument until the rechargeable batteries are

completely discharged.

Completely recharge the rechargeable batteries afterwards.

As a result, the life of the rechargeable batteries is significantly

increased.

Completely recharged batteries will slowly discharge during storage.

3.2

External Voltage Supply

For an external voltage supply the connector socket (4) is located at the right
side of the device. The range of accessories includes the mains adapter ZB
2290-NA (12V/200mA). However, any other DC voltage source (7 to 13V) can
also be used. The connection is performed by a low-voltage connector (NES1
according to DIN 42323, centre pin to negative).
The electrically isolated supply cable ZB 2290-UK must be used if an

electrical isolation

between power supply and transducers is required or if a

larger input voltage range is required. It allows to operate the measuring
instrument with 12V or 24V mains supply.

If a battery is used in addition it will take over the power supply
if the voltage drops under 9V.

ALMEMO



2290-2/3

13

Power Supply

«
...
11
12
13
14
15
...
»

Содержание ALMEMO 2290-2/3













































Отзывы:

Нет отзывов

Похожие инструкции для ALMEMO 2290-2/3

Бренд: LaserLine Страницы: 24

PLATINUM Series

Бренд: Hach Страницы: 64

Бренд: NCTE Страницы: 10

Бренд: P3 International Страницы: 1

Бренд: LEM Страницы: 33

Бренд: Clavitech Страницы: 56

Бренд: Solartron Mobrey Страницы: 34

Бренд: Analog Arts Страницы: 8

Heavy Duty 2270-20

Бренд: Milwaukee Страницы: 33

Бренд: Raytech Страницы: 7

WARREN ELLIS SIGNATURE TENOR BARITONE

Бренд: Eastwood Guitars Страницы: 4

Бренд: Fluke Страницы: 32

Multifunction Compensator

Бренд: Halcyon Страницы: 20

Бренд: Megasat Страницы: 25

Бренд: Thermocable Страницы: 10

Thruline 4020 Series

Бренд: Bird Electronic Страницы: 59

Бренд: Joinwit Страницы: 24

Бренд: HyQuest Solutions Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды