manualshive.com logo in svg

Agri-Fab 45-03503, Руководство пользователя

Поделиться
Скачать
Agri-Fab 45-03503 Скачать руководство пользователя страница 5

5

FIGURE 5

FIGURE 6

FIGURE 4

FIGURE 7

AXLE

DRAW BAR
TONGUE

LATCH STAND
BRACKET

9. 

Assemble the front panel over the end of the cart 
using six 1/4" x 5/8" (F) hex bolts and 1/4" nylock 
nuts (H) as shown in figure 4. Leave two holes in the 
bottom of the panel empty as shown. Pull the cart 
body halves together and

 tighten 

the bolts in the 

bottom of the front panel, then 

tighten

 the bolts in the 

sides

.

 See figure 4.

10. 

Tighten

 the bolts assembled in step 4 to fasten the 

bottom of the cart together.

 1/4" x 5/8"
HEX BOLTS (F)

1/4" NYLOCK NUT (H)

1/4" NYLOCK 

NUT (H)

LEAVE HOLES OPEN FOR 

LATCH STAND BRACKET 

 

5/16"

NYLOCK

NUT (J)

 

WHEEL 

SUPPORT 

5/16" x 3/4" TRUSS

HEAD BOLT (D)

11. 

Assemble the latch stand bracket  to the cart so that 
the aligning tab is at the bottom of the bracket. Use 
four 1/4" x 5/8" hex bolts (F) and 1/4" nylock nuts (H). 

Tighten.

 See figure 5.

12. 

Assemble a corner cap to each front corner using 
one 1/4" x 5/8" hex bolt (F) and 1/4" nylock nut (H) 
per cap. 

TIGHTEN.

 See figure 5.

13. 

Assemble the wheel support to the cart using eight 
5/16" x 3/4" truss head bolts (D) and 5/16" nylock 
nuts (J) as shown in figure 6. Heads of bolts go on 
the inside of the cart. 

Tighten.

14. 

Lower the cart to rest upside down on its top flange 
with the wheel support facing up.  See figure 7.

15. 

Lay the drawbar tongue (open side facing up) onto 
the Wheel Support and the Latch Stand Bracket. 
Slide the axle through the wheel support and the 
tongue. See figure 7.

1/4" x 5/8"

HEX BOLT (F)

LATCH STAND BRACKET 
(Aligning tab at bottom) 

1/4" x 5/8"

HEX BOLT (F)

1/4" NYLOCK 

NUT (H)

CORNER 
CAP 

1/4" NYLOCK 

NUT (H)

Содержание 45-03503





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды