background image

5

Symbols used in this manual

V……..volts
A……..amperes
Hz……hertz
W……..watt
~………alternating current
n

0

………no load speed

min

-1

……..revolutions or reciprocation per minute

………….class II tool

                                                     SPECIFIC SAFETY RULES
 
1.  Keep hands away from rotating sanding head area at all times! 
2.  Prolonged breathing of airborne dust from drywall sanding may effect 

respiratory function:

  

Always use a vacuum cleaner with a bag approved for drywall dust installed. 

  

Always wear a respirator approved for dust and mist.

3.  Sanding LEAD-BASED paint is extremely toxic and should not be attempted. 

Only allow professionals with special training and equipment perform this task.

4.  Maintain proper footing and balance at all times. Do not overreach. Use proper 

scaffolding

5.  Always wear appropriate safety equipment when operating.
6.  Important: After completing sanding,
 switch off the switch and wait for the 

coasting sanding head to stop completely before putting the tool down.

7.  Never operate the tool in an area with flammable solids, liquids, or gases. Sparks 

from the commutator/carbon brushes could cause a fire or explosion.

8.  There are certain applications for which this tool was designed. The 

manufacturer strongly recommends that this tool NOT be modified and/or used 
for any application other than for which it was designed. If you have any 
questions relative to its application DO NOT use the tool until you have written 
the manufacturer and have been advised.

9.  Use the machine with both hands at all times. Loss of control can cause 

personal injury.

10.  Keep power supply cord clear from the working range of the machine. Always 

lead the cable away behind you.

11.  Immediately switch off the machine if unusual vibrations or if other malfunctions 

occur. Check the machine in order to find out the cause.

12.  The dust that arises when working with this tool can be harmful to health. Use a 

dust absorption system and wear a suitable dust protection mask and remove 
deposited dust with a vacuum cleaner. 

Содержание HS225





















Отзывы: