Agora Models Bismarck 06 Скачать руководство пользователя страница 7

Страница: 7 / 39

. TESTING THE MOTORS AND LIGHTS

First, we test the two radar units,

34-02

and

37-02

. In order to do this, connect the

battery box

4-07

to the circuit board

4-06

Plug the cable marked

B-18

into the free

socket on the circuit board

4-06

. Now switch

the battery box to “On”. The radar
unit

37-02

will turn. Switch off the battery

box before proceeding. Connecting cable

B-19

to the circuit board

4-06

turns the radar unit

34-02

. You can also test the firing of the second

38cm gun turret by plugging the cable marked

B-21

into the circuit board (inset).

NOTE:

Extreme care is needed when

testing the LED lights. Only connect
them to the new circuit board

57-09

otherwise permanent damage could
occur.
Next, we test the lights of the forward
superstructure. With the battery box
switched off, remove the circuit board

4-06

and plug in the circuit board

57-09

. Plug the cable marked

B-9

into

the free socket on the circuit board. Now
switch on the battery box: the
searchlight

40-07

comes on. Switch off

the battery box before continuing.

Next we test the lights of the forward
superstructure. It is essential that this is
only done with the new circuit board

57-09

. By plugging different cables

into the circuit board

57-09

, different

lights can be switched on, as follows:

B-5:

Green navigation light

B-6:

Red navigation light

B-7:

Bridge light

B-8:

Lights on the admiral’s bridge

B-9:

Searchlight

NOTE:

Always switch off the power

supply when connecting or
disconnecting cables.

57-09

4-07

4-06

B-18

37-02

34-02

4-07

B-9

40-07

B-9

B-8

B-5

B-7

B-6

B-18

AGORA

MODELS

AGORA

MODELS

Содержание Bismarck 06








































Результаты поиска

Содержание Bismarck 06

Отзывы:

Бренды по названию

Популярные бренды

Agora Models Bismarck 06, Инструкции по сборке

Результаты поиска

Содержание Bismarck 06

Отзывы:

Бренды по названию

Популярные бренды