manualshive.com logo in svg

Agora Models Bismarck 06, Инструкции по сборке

Поделиться
Скачать
Agora Models Bismarck 06 Скачать руководство пользователя страница 22

03

04

05

06

Fit the cover 

63-07

 over the motor 

62-01

, ensuring 

that the screw holes on the cover align with those on 
the upper deck section 

22-01

. 

Fix the cover 

63-07

 in place using two 

PB

 screws. 

Support the deck from below while tightening  
the screws.

Take the funnel cap 

63-04

 and the grille 

63-01

. Apply 

a little superglue to the edge of the grille 

63-01

 and 

fix it in place on the funnel cap as indicated. Note that 
the flatter side of the grille is uppermost (see step 3). 

Place the funnel base plate 

63-02 

on the work  

surface with the raised sections facing upwards.  
Apply a little superglue to the pegs on the underside 
of the grille 

63-01

 and fit the funnel cap and grille 

over the base plate. 

02

. THE TOP OF THE FUNNEL

01

02

This shows the funnel cap assembled. Note that  
one end of the cap is higher than the other: the  
higher end goes at the forward end of the funnel  
in the following step.

Take the funnel assembly from stage 

61

. Note that the 

curved end of the funnel is the forward end. Apply a 
little superglue around the rim of parts 

61-05/61-06

 

and fix the funnel cap assembly in place.

PB

61-05

63-07

62-01

63-07

22-01

63-01

63-04

63-02

63-01

63-02

63-01

61-06

63-04

03

04

22

22

AGORA

MODELS

23

AGORA

MODELS

Содержание Bismarck 06








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды