Agilent Technologies U2751A Скачать руководство пользователя страница 51

Страница: 51 / 57

Service Information

U2751A User’s and Service Guide

Replaceable Parts

This section contains the information for ordering
replacement parts for your instrument. To order the parts,
please do the following.

•

Contact your nearest Agilent Sales Office or Service
Center.

•

Provide the part number for the relay.

•

Provide the instrument model and serial number.

The part number of the replaceable part and its description
are shown in the table below.

Table 4-2

Part number and description of replaceable part

Part number

Description

0490-1896

RELAY 2C 3 VDC-COIL 2A 30 VDC

C A U T I O N

Electrostatic Discharge (ESD) Precautions

Almost all electrical components can be damaged by electrostatic
discharge (ESD) during handling. The following guidelines will help
prevent ESD damage when servicing the instrument or any electronic
device.

•

Disassemble the instruments in a static-free work area

only

•

Use a conductive work area to dissipate static charge.

•

Use a conductive wrist strap to dissipate static charge
accumulation.

•

Minimize handling.

•

Keep the replacement parts in original static-free packaging.

•

Remove all plastics, styrofoams, vinyls, papers, and other
static-generating materials from the immediate work area.

•

Use

only

antistatic solder extractor.

Содержание U2751A


























































Результаты поиска

Содержание U2751A

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies U2751A, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание U2751A

Отзывы:

Бренды по названию

Популярные бренды