manualshive.com logo in svg

Agilent Technologies U2751A, Руководство пользователя и сервисное руководство

Поделиться
Скачать
Agilent Technologies U2751A Скачать руководство пользователя страница 30

14

U2751A User’s and Service Guide

1

Getting  Started

U2922A Terminal Block Installation

This section provides the recommended procedure for 
connecting the U2922A terminal block to the U2751A.

WA R N I N G

• The maximum working voltage of the U2751A with the 

terminal block for standalone is 35 Vrms and for 
modular (when used with the U2781A) is 180 Vrms.

• The maximum transient voltage is 300 Vrms.

• Do not remove the retractable cover from the U2922A 

terminal block during operation to avoid any 
unexpected hazard.

N O T E

•

You are required to connect the cables to the U2922A terminal block 
prior to attaching the U2922A to the U2751A. 

•

Ensure that you power-off your device and unplug the U2922A from the 
U2751A to change the cable connection on the U2922A.

Connect the cables to the terminal block as 
desired.

cables

Содержание U2751A


























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды