Agilent Technologies U2751A Скачать руководство пользователя

Страница: 44 / 57

U2751A User’s and Service Guide

Characteristics and Specifications

Product Characteristics

REMOTE INTERFACE

•

Hi-Speed USB 2.0

•

USBTMC 488.2 Class device

POWER CONSUMPTION

•

+12 VDC, 2 A maximum

•

Installation Category III

OPERATING ENVIRONMENT

•

Operating temperature from 0

C to +50

•

Relative humidity at 20% to 85% RH (non-condensing)

•

Altitude up to 2000 meters

•

Pollution degree 2

•

For indoor use only

STORAGE COMPLIANCE

–20

C to +70

SAFETY COMPLIANCE

Certified with:

•

IEC 61010-1:2001/EN61010-1:2001 (2nd Edition)

•

Canada: CAN/CSA-C22.2 No. 61010-1

•

USA: ANSI/UL 61010-1:2004

EMC COMPLIANCE

•

IEC 61326-2002/EN61326:1997+A1:1998+A2:2001+A3:2003

•

Canada: ICES-001:2004

•

Australia/New Zealand: AS/NZS CISPR11:2004

SHOCK AND VIBRATION

Tested to IEC/EN 60068-2

I/O CONNECTOR

DSub 25 male

DIMENSIONS (W

•

105.00

175.00

25.00 mm (without bumpers)

•

117.00

180.00

41.00 mm (with bumpers)

WEIGHT

•

428 g (without bumpers)

•

480 g (with bumpers)

Содержание U2751A


























































Результаты поиска

Содержание U2751A

Отзывы:

Похожие инструкции для U2751A

Бренды по названию

Популярные бренды

Agilent Technologies U2751A, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание U2751A

Отзывы:

Похожие инструкции для U2751A

Бренды по названию

Популярные бренды