manualshive.com logo in svg

Agilent Technologies ESA E4401B, Установочная инструкция, Страница: 3 / 10

Поделиться
Скачать
Agilent Technologies ESA E4401B Скачать руководство пользователя страница 3

Installation Note E4411-90051

 3

Tracking Generator Retrofit Kit

Introduction

These kits contain the parts and instructions to install a 50

Ω

 Tracking Generator (Option 1DN) or a

75

Ω

 Tracking Generator (Option 1DQ). A 75

Ω

Tracking Generator should not be installed in an

analyzer with a 50

Ω

input. Similarly, a 50

Ω

Tracking Generator should not be installed in an analyzer

with a 75

Ω

input.

Installation Kit Parts List

Table 1. 50

Ω

 Tracking Generator Kit (Option 1DN) E4401-60175

Table 2. 75

Ω

 Tracking Generator Kit (Option 1DQ) E4401-60176

Products Affected: . . . . . . . . . . . . . . . . . . . . . . . . .

E4401B
E4411A
E4411B

Serial Numbers: . . . . . . . . . . . . . . . . . . . . . . . . . . .

US00000000/US99999999

To Be Performed By: . . . . . . . . . . . . . . . . . . . . . .

(x) Agilent Service Center
(x) Personnel Qualified by Agilent
(x) Customer

Estimated Installation Time: . . . . . . . . . . . . . . . .

1 Hour

Estimated Verification Time: . . . . . . . . . . . . . . . . .

2 Hours

Item

Quantity

Description

Part Number

1

1

Board Assembly Tracking Generator, 50

Ω

E4401-60128

2

1

Adapter, Type-N(m) to STET (f), 50

Ω

1250-0780

3

4

Screw, M3 x 8 mm (crest washer - pan head - TORX)

0515-0372

4

1

Installation Note (this document)

E4411-90051

Item

Quantity

Description

Part Number

1

1

Board Assembly Tracking Generator, 75

Ω

E4401-60129

2

1

Adapter, BNC(m) to F(f), 75

Ω

1250-2477

3

4

Screw, M3 x 8 mm (crest washer - pan head - TORX)

0515-0372

4

1

Installation Note (this document)

E4411-90051

Содержание ESA E4401B











Отзывы:

Нет отзывов