Agilent Technologies E8401A Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 66

Agilent Technologies E8401A Скачать руководство пользователя страница 15

Getting Started

13

Chapter 1

Front Panel Features

Figure 1-4. Agilent E8401A and E8403A Basic Monitoring Front Panel

Section

Indicator / Switch

Description



Power

On Indicator

Standby Indicator

Green - the mainframe is turned on.

Amber - the mainframe is in standby mode; no power is applied to the VXI modules.



Supply

Voltages Indicator

Temp Indicator

Green - all voltages on the VXI backplane are within ±8% of the VXI specification.

Flashing Amber - one or more voltages is out of specification. The backplane voltages
and allowed variations are listed below:

Voltage   Allowed Variation    Diagnostic Pin
+5V    +4.875V to +5.125V      1
+12V    +11.64V to +12.6V      14
-12V -12.6V to   -11.64V     2
+24V    +23.28V to +25.2V    15
-24V -25.2V to   -23.28V    3
-5.2V -5.46V to   -5.044V    16
-2V -2.1V to   -1.9V    4

Green - the power supply temperature is acceptable.

Flashing Amber - the power supply is approaching thermal shutdown. The power supply
temperature can be measured on pin 11 of the Diagnostic connector.



Fans

Fan Switch

Fans Indicator

Full - the power supply and mainframe cooling fans are operating at full speed.

Var(iable) - the power supply and mainframe cooling fans are providing adequate cooling
(default setting). Fan speed is a function of the power supply temperature and the
reference temperature (Diagnostic connector pin 12). The reference temperature is a
function of ambient temperature and load.

Green - the power supply and mainframe cooling fans are operating.

Flashing Amber - the power supply fan

or

the mainframe cooling fan is not operating. Fan

operation can be checked using pin 13 of the Diagnostic connector.



Backplane

Activity Indicator

SYSFAIL Indicator

Reset Switch

Green - there is communication between instruments across the backplane. Off - there is
no communication between instruments on the backplane.

Flashing Amber - one or more instruments has asserted its SYSFAIL line due to a
power-on initialization failure, self-test failure, or hardware failure. SYSFAIL is asserted
momentarily at power on and during a system reset.

Pressing the reset button asserts the SYSRESET* line on the VXI backplane. When
asserted (low), this line resets the VXI system; all VXI instruments are rest to their
power-on state.



Diagnostic
Connector

Refer to “Diagnostic Connector” on page 14.

«
...
13
14
15
16
17
...
»

Содержание E8401A



































































Отзывы:

Нет отзывов