manualshive.com logo in svg

Agilent Technologies E8363A, Установочная инструкция

Поделиться
Скачать
Agilent Technologies E8363A Скачать руководство пользователя страница 4

4

  

                                                                                                                            

  

Installation Note E8364-90012

About Installing the Upgrade Kit

Description of Option 014 

An Option 014 analyzer can be configured to measure high-power devices and devices for high 
dynamic range.

For a high-power measurement, external amplifiers and high power attenuators or isolators 
can be added to complete the test setup. In this configuration, test port output power up to 
1 Watt (+30 dBm) can be applied to the device under test (DUT). Additionally, there is an 
external reference input that allows the external amplifier’s frequency response and drift to 
be ratioed out.

For high dynamic range measurements, front panel jumpers are moved to reverse the signal 
path through one of the couplers. This allows for a 15 dB improvement in transmitted signal 
sensitivity in one direction only. These jumpers are installed on both ports allowing the user 
to choose a high dynamic range measurement in either the forward or reverse direction.

Products affected . . . . . . . . . . . . . . . . . . . . . . . . . . E8363A and E8364A; all options

Installation to be performed by  . . . . . . . . . . . . . . Agilent service center or personnel 

qualified by Agilent

Estimated installation time . . . . . . . . . . . . . . . . . 2.0 hours

Estimated adjustment time  . . . . . . . . . . . . . . . . . 0.5 hours

Estimated full instrument calibration time  . . . . 4.5 hours

Содержание E8363A





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды