manualshive.com logo in svg

Agilent Technologies E8363A, Установочная инструкция

Поделиться
Скачать
Agilent Technologies E8363A Скачать руководство пользователя страница 14

14

  

                                                                                                                            

  

Installation Note E8364-90012

Analyzers with Option UNL

Refer to 

Figure 8

 for the following procedure. The new parts referenced in this procedure are 

listed in 

Table 1 on page 5

.

If you are installing Option 014 on an analyzer that has Option UNL installed, install the 
following cables in the order listed:

• W70 E8364-20049 REFERENCE 1 RCVR R1 IN to A28 channel R1 mixer

• W71 E8364-20050 REFERENCE 2 RCVR R2 IN to A29 channel R2 mixer

• W68 E8364-20044 A26 test port 1 coupler to PORT 2 CPLR ARM

• W72 E8364-20046 PORT 2 RCVR B IN to A30 channel B mixer

• W82 E8364-20054 A37 step attenuator to PORT 2 SOURCE OUT

• W84 E8364-20040 PORT 2 CPLR THRU to A39 bias tee 

• W66 E8364-20048 A24 detector to REFERENCE 2 SOURCE OUT

• W67 E8364-20043 A25 test port 1 coupler to PORT 1 CPLR ARM

• W69 E8364-20045 PORT 1 RCVR A IN to A27 channel A mixer

• W81 E8364-20053 A36 step attenuator to PORT 1 SOURCE OUT

• W83 E8364-20039 PORT 1 CPLR THRU to A38 bias tee

• W65 E8364-20047 A23 detector to REFERENCE 1 SOURCE OUT

Figure 8

Option 014 Cable Installation, Analyzers with Option UNL

Содержание E8363A





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды