Agilent Technologies 85032F Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 48

background image

2-2

85032F

Specifications

Environmental Requirements

Environmental Requirements

NOTE

Samples of this product have been type-tested in accordance with the Agilent
Environmental Test Manual and verified to be robust against the
environmental stresses of storage, transportation and end-use; those stresses
include but are not limited to temperature, humidity, shock, vibration,
altitude and power-line conditions. Test methods are aligned with IEC

60068-2 and levels are similar to MIL-PRF-28800F Class 3.

Temperature—What to Watch Out For

Changes in temperature can affect electrical characteristics. Therefore, the operating
temperature is a critical factor in performance. During a measurement calibration, the
temperature of the calibration devices must be stable and within the range shown in
Table 2-1.

IMPORTANT

Avoid unnecessary handling of the devices during calibration because your
fingers are a heat source.

Table 2-1

Environmental Requirements

Parameter Limits

Temperature

Operating

a

a. The temperature range over which the calibration standards maintain conformance to their

specifications.

+20

°

C to +26

°

C

Storage

−

40

°

C to +75

°

C

Error-corrected range

b

b. The allowable network analyzer ambient temperature drift during measurement calibration

and during measurements when the network analyzer error correction is turned on. Also, the
range over which the network analyzer maintains its specified performance while correction
is turned on.

±

1

°

C of measurement calibration temperature

Altitude

Operating

< 4,500 meters (

≈

15,000 feet)

Storage

< 4,500 meters (

≈

15,000 feet)

Relative humidity

Type tested, 0% to 95% at 40

°

C, non-condensing

«
...
12
13
14
15
16
...
»

Содержание 85032F

















































Отзывы:

Нет отзывов

Похожие инструкции для 85032F

Бренд: Parata Страницы: 40

Бренд: Rainbow Страницы: 18

Бренд: JB-Lighting Страницы: 32

Бренд: W&H Страницы: 72

Life/form SmartScope LF01142U

Бренд: Nasco Страницы: 2

Бренд: Tactile Medical Страницы: 23

Бренд: Taarup Страницы: 72

Бренд: TC Electronic Страницы: 4

Бренд: TC Electronic Страницы: 6

Бренд: TC-Helicon Страницы: 12

Бренд: TC Electronic Страницы: 76

Бренд: Ultraflex Страницы: 48

AURO SPOT CLAS100

Бренд: Cameo Страницы: 60

Бренд: Woods Страницы: 54

Бренд: GOZONE Страницы: 11

Бренд: Mercia Garden Products Страницы: 5

Бренд: Tatu Marchesan Страницы: 52

Add-It AFI 5016-H

Бренд: DIG Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды