Agilent Technologies 81150A Скачать руководство пользователя страница 97 | Manualshive

Страница: 97 / 102

background image

Installation and Maintenance

81150A and 81160A Getting Started Guide

97

4.3

Ventilation Requirements

Introduction

The instrument is fitted with three cooling fans. Make sure that there is
adequate clearance of 80 mm at the rear and 25 mm on both sides to ensure
adequate air flow. If the air flow is restricted the internal operating
temperature will be higher, reducing the instrument's reliability or causing
the instrument's thermal-protection circuits to automatically switch off the
instrument.

4.3.1

Thermal Protection

Overheating
Detection

The instrument monitors its internal temperature. If the temperature
exceeds approximately 80°C the power supply is switched off. The
instrument will not turn on automatically if the temperature is decreasing
again.

Fan Failure

If a fan is broken or prevented from operating by a blockage the temperature
will increase. When the temperature exceeds approximately 80°C the
overheating detection switches off the instrument for safety reasons. For
reliability it is recommended to send instruments with broken or defective
fans immediately to Agilent Service for repair.

«
...
95
96
97
98
99
...
»

Содержание 81150A







































































































Отзывы:

Нет отзывов

Похожие инструкции для 81150A

Бренд: National Instruments Страницы: 18

Бренд: Thulos Страницы: 5

Бренд: LONCIN Страницы: 27

Бренд: G-Power America Страницы: 53

Бренд: Pulsar Страницы: 26

Бренд: Circutor Страницы: 108

Бренд: Ceyear Страницы: 183

Бренд: Wagan Страницы: 13

Бренд: Rohde & Schwarz Страницы: 299

Бренд: Honda Страницы: 55

Бренд: EENOUR Страницы: 36

Бренд: Briggs & Stratton Страницы: 8

Бренд: Briggs & Stratton Страницы: 52

Vitobloc 200 EM-140/207

Бренд: Viessmann Страницы: 56

Бренд: Kubota Страницы: 63

Бренд: Harbor Freight Tools Страницы: 28

Бренд: DAISHIN Страницы: 36

Бренд: Zenit Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды