Agilent Technologies 4072A Advanced Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 84

background image

14

Chapter 2

Agilent 4072/4073 Preinstallation Guide, Edition 4

Site Preparation

Installation Site Requirements

Lighting

Provide sufficient lighting for optimum visibility of lighted indicators, the display, and the keyboard of the system
controller. Arrange lighting so that reflected light does not make it difficult to read displayed characters. Also, the
system, and especially the software media, must not be exposed to direct sunlight.

Software media storage

Purchase a fireproof cabinet or locker for storing important items, such as documents and software media

Software media such as CD-ROM should be stored in an environment similar to that of the 4072/4073 tester.
Extreme temperature or humidity changes, which may alter the size of a disk, must be avoided. Do not place the
software media in or near magnetic fields.

Telephone

Install a telephone with an extra-long receiver cord, to allow the operator easy access to any part of the system
while on the phone.

Network service

If the system controller is to be connected with a network, a network service and LAN cable are necessary. Choose
a long LAN cable that can connect with the system controller. Also, prepare the IP address and hostname before the
tester installation.

Label for emergency off switch

Install the 4072/4073 tester to enable easy access to the main breaker or switch and adhere conspicuous labels so
that the operator will be able to cut the main power quickly in an emergency.

Lock for disconnect device

Prepare a lock for the main switch, required for lockout during maintenance of the system. Determine the lock’s
suitability by considering the hole in the disconnect device. Figure 2-2 shows the dimensions of the lock.

Figure 2-2

Dimensions of lock

A

B

C

A

35 mm

40 mm

B

19 mm

21 mm

C

5 mm

6 mm

«
...
12
13
14
15
16
...
»

Содержание 4072A Advanced





















































































Отзывы:

Нет отзывов

Похожие инструкции для 4072A Advanced

Бренд: Tanco Страницы: 72

Бренд: HABYS Страницы: 16

Бренд: Acterna Страницы: 72

BELMONT 2001039

Бренд: Backyard Discovery Страницы: 50

Бренд: Backyard Discovery Страницы: 45

Бренд: Backyard Discovery Страницы: 70

Бренд: BACtrack Страницы: 16

Бренд: jcb Страницы: 41

Бренд: iFIT Страницы: 11

Бренд: lancer Страницы: 3

Бренд: lancer Страницы: 12

Бренд: R2 Страницы: 26

Бренд: R&S Страницы: 371

Бренд: R.M. Young Страницы: 9

Бренд: Toro Страницы: 4

Бренд: Tadano Страницы: 16

Бренд: Parkside Страницы: 88

DSO8000E Series

Бренд: Hantek Страницы: 95

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды