AGFA D2RS Скачать руководство пользователя страница 36

Страница: 36 / 40

Digital Remote Controlled Table with dynamic flat panel detector

User’s Manual

INFORMATION MESSAGES (TO BE CONTINUED)

Messages displayed on top of screen

description

What to do

TABLE TOP REAR LIMIT

This indicates that the tabletop reaches its end lateral position on rear side (column)

These messages are
informative and do not
require pressing any key.
These indications stay
displayed until any
change (other control ...).
If the message persists
when you order another
movement, turn the
system OFF and ON.
If the equipment remains
inoperative, turn it OFF
and call Field Service

TABLE TOP FRONT LIMIT

This indicates that the tabletop reaches its end lateral position on front side

ELEVATION LOWER LIMIT

This indicates that the tabletop reaches its lower position

ELEVATION UPPER LIMIT

This indicates that the tabletop reaches its higher position

Collimator Not Ready

This indicates that the collimator is opening or closing to the desired format

Compressor Upper limit

This indicates that the compression device reaches its higher position

Compressor Lower limit

This indicates that the compression device reaches its lower position

Tomography In Progress

This indicates that the tomography device is moving

Patient Compression Detected

This indicates that the system detects compression

Max. Compression Level Reached

This indicates that the maximum compression level is reached

Patient Compression Detected, Tube
Angulation Disabled

This indicates that the system detects compression and then forbids any
movement of angulation

In order to allow the
desired movement, lift UP
the compression device

Patient Compression Detected, Carriage
Disabled

This indicates that the system detects compression and then forbids any
movement of carriage

Patient Compression Detected, Lat. Table
Top Disabled

This indicates that the system detects compression and then forbids any lateral
movement of tabletop

Patient Compression Detected, Long.
Table Top Disabled

This indicates that the system detects compression and then forbids any
longitudinal movement of tabletop

TUBE ROTATED, FLUORO
DISABLED

This indicates that the X-ray tube is rotated and then not centred on the detector

Place X-ray tube faced to
detector, at 0 ° with the
indexing system.

NO AUTO POSITIONING SELECTED

This indicates that you did not select any anatomical programme so then no
autopositioning before pressing the MOVE button

Select an anatomical
programme before
wanting to position the
system by MOVE button

ELEVATION LOWER LIMIT:
TABLE IS TILTED

This indicates that the system cannot go lower the tabletop as table is tilted

To reach elevation lower
limit, untilt the table
before lowering

Column Angulation Is Not Enabled
For SID > 150 cm

This indicates that you are not allowed to make a column incidence if the SID is
over 150 cm

Decrease the SID under
150 cm to be able to make
an incidence

Position Reached

This indicates that the system reaches the selected position

Now, you can follow your
exam procedure

End of Stitching

This indicates that the system has just finished the last exposure of the stitching
programme

Now, you can end your
exam procedure

End of Tomography

This indicates that the system has just finished the last exposure of the
tomography programme

Now, you can end your
exam procedure

ROTATION IMPOSSIBLE,
PRESS MOVE
(for version with removable detector)

This indicates that the system cannot rotate the detector due to its support
position and selected programme

For version with
removable detector.
Press MOVE to cancel
carriage

Содержание D2RS









































Результаты поиска

Содержание D2RS

Отзывы:

Бренды по названию

Популярные бренды

AGFA D2RS, Руководство пользователя

Результаты поиска

Содержание D2RS

Отзывы:

Бренды по названию

Популярные бренды