10
USING YOUR ELECTRONIC CONTROL
NOTE
NOTE
Starting your appliance
The appliance will begin start up when initially plugged in or
when power resumes after a power outage. If the appliance
has been turned off during use, “OFF” will appear on the
display. To start the appliance from the “OFF” position press
and hold the ON/OFF button for three seconds.
Adjusting the temperature
To set the set temperature, press and continue to hold
“SET” button. After one second, set temperature will be
displayed. While holding “SET” button use the “WARMER”
or “COLDER” button to desired set temperature.
Momentarily pressing & releasing “SET” button will access
information menu of control. Refer to appendix A for infor-
mation on this feature.
Appliance operation
The available temperature range of the refrigerator is 2° to
8° C.
It may take up to 24 hours for your appliance to reach de-
sired temperature. This will depend on amount of contents
loaded and number of openings and closings of the drawer.
For best results allow the appliance to “pull down” to de-
sired set temperature before loading. Once contents are
loaded, allow at least 48 hours for temperature to stabilize
before making any adjustments to the set temperature.
Alarms
Your MicroSentry
II
™ appliance control will monitor ap-
pliance function and alert you with a series of audible and
visual alarms. For all alarm and error codes, the alarm
LED located in the top left corner of the display panel will
illuminate a steady amber. For all alarm and error codes
except condenser cleaning, an audible alarm will sound,
beeping in one (1) second intervals.
•
Door Ajar Alarm:
If the drawer has
been left open for over five (5) minutes, the
alarm will sound and the display panel will
flash “do.” The alarm will stop once the
drawer has been closed.
•
High and Low Temperature Alarm:
If
your unit reaches an unacceptable tempera-
ture, above or below your set temperature for
a period of greater than 60 minutes, the tem-
perature alarm will sound in one (1) second
intervals. The display panel will flash either
“hi” or “Lo” depending upon the condition. “hi” indicates a
high temperature alarm, and “Lo” indicates a low tempera-
ture alarm.
The factory preset for the "hi" and "Lo" temperature devia-
tion is +2°C from set temperature for the "hi" and -2°C from
set temperature for the "Lo". If these temperature variations
need to be adjusted, please call AGA Marvel customer
service at 800-223-3900 for instructions.
•
Temperature Sensor Fault:
If the control
detects that the temperature sensor is not
properly functioning, an audible alarm will
sound, and “E1” will flash on the display. Please call AGA
MARVEL customer service or your dealer if this error code
is displayed.
Alarm Mute
Press any key to mute the audible portion of an alarm.
This action will only mute the alarm. If the condition that
caused the alarm continues, the alarm code will continue to
flash and will sound for 20 seconds every 60 minutes.
Turning Appliance Off
To turn appliance off, press and hold “ON/OFF” button for
three (3) seconds. “OFF” will appear on the
display.
Additional MicroSentry
II
™ Features
Information Menu / Lockout Key
To access the information menu, press the SET key, and
immediately release it.
In the information menu, a 2 or 3 digit code will be dis-
played representing each entry in the information menu.
The first code displayed will be t1. With each sequential
press and release of the SET key, the following codes will
appear in this order: t1, t2, thi, tLo, FrM, and Loc.
(The t2
code only appears on the refrigerator).
To view the value of each code, press and hold the SET
key after the desired code is displayed. Additionally,
the WARMER and COLDER keys may be used to scroll
through the menu. To exit the information menu, press
the ON/OFF key, or wait for several seconds with no key
presses.
Figure 12
Control located
on face of top
drawer
Set
Colder
Warmer
ON/OFF
Press and Hold
Press and Hold
Alarm
F
C
