background image

  PAGE  6

 

2. INTRODUCTION AND SIGN-OFF FORM 

 

Congratulations! 

 on your choice of an Ag Shield LandRoller. This equipment has been designed and 

manufactured to meet the  needs of the discerning farmers and contractors, and rental agencies. 
 

OPERATOR ORIENTATION

 - The directions left, right, front and rear, as mentioned throughout this manual, 

are as seen from the tractor driver's seat and facing in the normal direction of travel. 
 
Ag Shield follows the general safety standards specified by the American Society of Agricultural Engineers (ASAE) 
and the Occupational Safety and Health Administration OSHA). Anyone who will be operating and/or maintaining the 
Ag Shield LandRoller must read and clearly understand ALL Safety, Operating, and Maintenance information 
presented in this manual. 
 
Do not operate or allow anyone else to operate this equipment until such information has been reviewed. Review this 
information annually before season start-up. Make these reviews of safety and operation a standard practice for all of 
your equipment.  An untrained operator is 

not qualified

 to operate this machine. 

 
A sign off sheet is provided for your record keeping to show that all personnel who will be working with the equipment 
have read and understood the information in the Operators Handbook and have been instructed in the operation of 
the equipment. 
 

SIGN-OFF FORM

 

 

DATE 

OPERATORS SIGNATURE 

EMPLOYERS SIGNATURE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Содержание LandRoller
























































Отзывы: