0
1
0
1
S4
0
1
S3
0
1
0...10 V / 0...20 mA
2...10 V / 4...20 mA
U/I
S5 S6
0
0
0
1
1
0
90s
120s
60s
0
1
U
I
Signal
S2
0
1
S1
1
1
120s
230 V (24 V) ~
N L
1 2 3
5
6
N
4
4
230 V (24 V) ~
N L
1
2
3
N
230 V (24 V) ~
N L
1
2
3
N L
230 V (24 V) ~
N L
1 2 3
5
6
N
4
4
L
AC 24 V
1 2 3
~
4
+
-
Y U
~
+ -
DC 24 V
Y DC 0(2)...10 V
0(4)...20 mA
U DC 0(2)...10 V
Figure 4
Figure 3
5
6
8
7
Page
Figure 5
Technical specifications
Warranty
Customer satisfaction
Taking out of service, disposal
Approvals and certificates
Setting the auxiliary switch (selected versions)
Maintenance
Operation of the actuator
Procedure for setting the auxiliary switch:
1.
3.
5.
4.
2.
Loosen two fixing screws "i" and
remove the actuator housing
(fig. 1)
.
Carefully push in the ring in such a way that
the end of the thicker section of the
circumference coincides with the specified
switch triggering angle.
Refit the upper part of the actuator housing
and tighten the fixing screws "i".
After the actuator has been set to position
"5" of the adjustment scale at the adjustment
handle (50 % open) and the valve opening
direction has been determined, set the angle
of the actuator (range 0 - 90°) at which the
function of the auxiliary switch is to be
triggered.
Carefully remove the switching ring
(fig. 5)
. The thicker ring section which
moves below the switch while the
actuator operates, applies pressure to
the lever and thus opens of contacts
4-5 of the auxiliary switch.The function
of the auxiliary switch (closing of
contacts 4-5) is initiated when the
thinner ring section faces the switch
which triggers the lever. At the same
time, the signal lamp lights up.
The AFRISO ARM actuator is maintenance-free.
3-point
2-point
proportional
3-point + auxiliary switch
3-point + auxiliary switch
The electrical actuator ARM complies with the Low Voltage Directive (LVD) (2006/95/EC),
Electromagnetic Compatibility Directive (EMC) (2004/108/EC) and Restriction
of Hazardous Substances Directive (RoHS) (2002/95/EC)
The electrical actuator ARM also complies with the following standards:
EN 60730-1, EN60730-2-14.
The warranty of the manufacturer for this
product is 36 months after the date of
purchase. The warranty shall be void if
unauthorised modifications are made to the
product or if the product is not installed in
compliance with these instructions.
Customer satisfaction is the prime objective of
AFRISO-EURO-INDEX. Please contact us at
[email protected] if you have any questions,
suggestions or problems concerning product.
1.
2. Dismount the device.
3. To protect the environment, this
device must not be disposed of
together with non-separated
Disconnect the device from the
supply voltage.
commercial waste. Take the device to
an official waste disposal company.
The electrical actuator ARM consists of
recyclable materials.
1. Operating mode of the actuator
2. Indication via signal LEDs
The operating mode is set by means of
the selector for manual mode "j"
(fig. 1)
.
Operating mode Automatic:
The actuator
is in operating mode Automatic when the
selector "j" is in position .
Operating mode Manual:
The actuator is in
operating mode Manual when the selector
"j" is in position .
Three signal LEDs are integrated into the
housing of the actuator. The outer LEDs
indicate the direction of rotation of the
actuator. The centre LED indicates the
operating state of the auxiliary switch
(depending on the version of the actuator).
3. Position of adjustment handle with
adjustment scale
After the actuator has been mounted to the
mixing valve and the proper adjustment
scale selected, position "0" means that the
valve is fully closed (hot water supply
closed) and position "10" means that the
valve is fully opened (hot water supply
open). The other settings of the adjustment
scale represent the degree of opening
(for example, "4" means that the valve is
open by 40%).
orange
(direction of rotation left)
orange
(direction of rotation right)
red
(auxiliary switch active)
Parameter
Value
Torque
Depending on version:
6 Nm, 10 Nm, 15 Nm
Rotation angle
90°
Time for turn by
90°
Depending on version:
15 s, 30 s, 60 s, 120 s, 240 s, 480 s
Supply voltage / control signal
2-point
- 24 V AC / 230 V AC
3-point
- 24 V AC / 230 V AC
proportional - 24 V AC/DC
(0..10 V, 2..10 V, 0..20 mA, 4..20 mA)
Operating temperature range
Setting in range
0 ÷ 90° (250 V AC, 3 A)
Power input
0 ÷ 50°C
Power consumption
2,5 ÷ 4 VA
Protection class
II
Degree of protection
IP42
Dimensions (H x W x D):
84 × 102 × 90 mm
Weight
Version 6 Nm: 390 g ÷ 630 g
Version 10 Nm and 15 Nm: 600 g ÷ 860 g
Housing material
PC
instrukcja prosta do pudelka.indd 2
11-04-05 10:50
