AEV Roof Rack Скачать руководство пользователя страница 13

Страница: 13 / 13

Important Information:

Maximum carrying capacity: AEV can not recommend a weight carrying capacity. Refer to

your Jeep owner’s manual.

It is essential that all bolt connections are checked after driving a short distance when you first

install your AEV Roof Rack. Bolt connections should be checked again at regular intervals (proba

bly once a week is enough, depending on road conditions, usage, loads, and distances travelled).

Make sure to fasten your load securely. Please ensure that all loads are evenly distributed and

that the center of gravity is kept as low as possible.

USE ONLY NON-STRETCH FASTENING ROPES OR STRAPS.

SENSITIVITY TO CROSSWINDS BEHAVIOR IN CURVES AND BRAKING.

The handling characteristics of the vehicle change when you transport a load on the roof. For

safety reasons, we recommend you exercise extreme care when transporting wind resistant

loads, special consideration must be taken into account when braking.

Note for dealers and fitters

. It is your responsibility to ensure instructions are given to the end

user or client.

comments or questions?

American Expedition Vehicles

www.aev-conversions.com
email: [email protected]

ph: 248.926.0256

Be sure to visit our forum at: http://forum.aev-conversions.com

Содержание Roof Rack













