6
Horizontal Stabilizer with elevator assembly
—covered
(12) six per elevator, pin point hinges (
glued
) -
Ready
to
fly
Elevators
Pre-drilled
for the mounting of the
control
horns
Rudder
with (8) pin point hinges (
not glued
) – covered
Rudder Pre-drilled for the mounting of the
hinges, control horns and tail wheel steering arm.
SUB ASSEMBLIES:
#1:
(1) Fiberglass Cowling- painted - top and bottom- with
pre installed engine baffling, (22) pre drilled
screw holes for attaching top to bottom
(14) 4-40 blind nuts installed for attaching top to bottom
(14) 4-40 hex style bolts for attaching top to bottom
(8) 4-40 x 16mm hex bolts for mounting cowl to fuse
(8) #6 bonded washers for mounting cowling
(8) 3mm split lock washer for mounting cowling
#2:
(1) 6mm 7075Aluminum Main Landing Gear -- painted
(2) 5 x 48mm Axle Bolts
(2) M8 lock nuts
(4) 5mm i.d. Wheel Collars with set-screws
(2) 115mm Dia. Main Wheels (Lite Type)
(4) 4-40x16mm hex style bolts for mounting wheel
pants
(4) 3mm flat washer for mounting wheel pants
(4) 3mm split ring lock washer for mounting wheel
pants
(4) 8-32x25mm hex head bolts for mounting main
landing
gear
(4) 4mm flat washers for mounting main landing gear
(4) 4mm split ring lock washers for mounting main
landing gear.
#3:
(2) Wheel Pants- Painted- pre mounted- 1 Left and 1
Right--
(4) 4-40 blind nuts installed in the wheel pants, 2 per
side.
(2) Landing gear cuffs - 1 left and 1 right - painted -
pre
installed
(4) 4-40 x 7mm hex head bolts for mounting cuffs
(4) 3mm flat washer for mounting cuffs
(4) 3mm split ring lock washer for mounting cuffs
#4:
(1) AW- Custom Carbon Tail Wheel Assembly
(1) Aluminum steering arm and mounting screws
(2) Steering springs
#5:
(1) 40mm O.D. x 1240mm Carbon wing tube
(1) 16mm O.D. x 230mm Carbon stab tube - Front
(1) 16mm O.D. x 460mm Carbon stab tube - Rear
(4) 8-32 x 25mm Hex head bolts for wing mounting
(4) #8 bonded washer for wing mounting
(4) 4mm split ring lock washers for wing mounting
(4) 4-40x16mm Hex style head bolts for stab mounting
(4) #6 bonded washer for stab mounting
(4) 3mm split ring lock washers for stab mounting
(4) 1.8mm cotter pins - Second method -wing mounting
for
security
#6:
(6) 4-40 2-1/2” Two end threaded pushrod with nuts and
clevises for ailerons
(4) 4-40 3” Two end threaded pushrod with nuts and
clevises for elevators
(2) 4-40x300mm Threaded pushrod –Throttle and
Choke
(2) 4-40 solder coupler - Throttle and Choke
(2) 4-40 Metal clevises - Throttle and Choke
(12) Brass spacers – 6 for ailerons; 4 for elevators; 1 for
throttle; 1 for choke
(22) 4-40 Ball Links – 12 for ailerons; 8 for elevators; 1
for throttle; 1 for choke
(22) 4-40 x 16mm hex style bolts
(22) 4-40 lock nuts
(1) 16”
Carbon tube
- pushrod reinforcement
#7:
(2) 1x1500mm plastic coated pull-pull steel cable.
(4) 4-40 Metal R/C links with metal clevises and nuts
(4) 3.5 x 5mm brass pull-pull swaging tubes
(12) AW double control horns
(72) T2.6 x 16mm Phillips head mounting screws
(2) 4-40 Ball Links
(2) 4-40 x 16mm hex style bolts
(2) 4-40 lock nuts
#8:
(1)
1500cc (50 ounce) Gas Fuel Tank assembly (Fuel)
(1) 1000cc (34 ounce) Gas Fuel Tank assembly (Smoke)
(1) 4ft. large gas fuel line
(4) Brass barbs for fuel line
#9:
(2) Throttle – Choke servo mounting plates
(4) Engine mounting templates
(DA150, 3W150 - 157, ZDZ 160 and ZDZ J-160)
(1) pre cut balsa sheet for canister tunnel- (3 pcs /set)
(2) Canister mounting bracket - Plywood
(16) 11mm O.D. x 20mm silicon tubes – canister pipe
(4) Rubber grommets - fuel line guide
(2) Cowl templates - cutting Hot Air exit holes
(1) 160 x 140 x 6mm foam for the Fuel tank.
(1) 160 x 100 x 6mm foam for the Smoke tank
(2) 300 x 80 x 8mm foam for the receiver and battery
(10) 3mm Nylon ties- fuel line
(8) 8mm Nylon ties - fuel tank
(6) 356 x 12.5mm Velcro (one wrap) Strap - Receiver
-Batteries
