6
Horizontal Stabilizer with elevator assembly with (12)
pin point hinges (glued)---covered
Elevators Pre-drilled for the mounting of the con-
trol
horns
Rudder with (7) pin point hinges (not glued) – covered
Rudder Pre-drilled for the mounting of the con-
trol horns
SUB ASSEMBLIES:
#1:
(1) Fiberglass Cowling w/ inside ring glued—painted
with (2) screws holes at bottom and (2) 6-32 blind
nuts installed
(2) 4-40x16mm hex style bolts for mounting cowling
(2) #6 bonded washers for mounting cowling
(2) 3mm split lock washers for mounting cowling.
(2)6-32x16mm hex head bolts for mounting cowling
(2) #6 bonded washers for mounting cowling
#2:
(1) 5mm 7075Aluminum Main Landing Gear --
painted
(2) 5x48mm AL Axle Bolts
(2) M8 lock nuts
(4) 5mm i.d. Wheel Collars with set-screws
(2) 100mm Dia. Main Wheels (Lite Type)
(4) 4-40x14mm hex style bolts for mounting wheel
pants
(4) 3mm flat washer for mounting wheel pants
(4) 3mm split ring lock washer for mounting wheel
pants
(4) 8-32x20mm hex head bolts for mounting main
landing gear
(4) 4mm flat washers for mounting main landing
gear
(4) 4mm split ring lock washers for mounting main
landing gear.
#3:
(2)Wheel Pants—1 Left and 1 Right---Painted
(4) 4-40 blind nuts installed on the wheel pants, 2 per
side.
#4:
(1) AL Tail Wheel Assembly with Rubber wheel –
LARGE
#5:
(1) 40mm o.d. Aluminum Tube for wing joint—
Anodized Black
(2) 12.5mm o.d. Aluminum Tube for stab joint – one
front and one rear, Anodized Black
(4) 8-32x25mm Hex head bots for wing mounting
(4) #8 bonded washer for wing mounting
(4) 4mm split ring lock washers for wing mounting
(4) 4-40x16mm Hex style head bolts for stab mount-
ing
(4) #6 bonded washer for stab mounting
(4) 3mm split ring lock washers for stab mounting
(4) 1.8mm cotter pins
#6:
(4) 4-40 3” Left hand and Right hand threaded push
rods with nuts and carbon tubes for ailerons
(2) 4-40 2-1/2” Left hand and Right hand threaded
pushrods with nuts and carbon tubes for elevators
(1) Wrench for the left hand and right hand
threaded pushrod
(2) 4-40x300mm Threaded pushrods
(2) 4-40 solder coupler with nuts
(2) 4-40 Metal clevises
(10) brass spacers – 4 for ailerons; 2 for elevators; 2
for throttle; 2 for choke
(16) 4-40 Ball Link – 8 for ailerons; 4 for elevators; 2
for throttle; 2 for choke
(16) 4-40x16mm hex style bolts
(16) 4-40 lock nuts
(16)
Φ
3mm flat washers
#7:
(2) 1x1300mm plastic coated pull-pull steel cable.
(4) 4-40 Metal R/C links with nuts
(4) 3.5x5mm brass pull-pull swaging tubes
(8) AL double control horns
(36) T2.6x16mm Phillips head mounting screws
(12) T2.6x12mm Phillips head mounting screws
(2) 4-40x36mm left hand and right hand threaded
pushrod for connecting rudder servo
(4) 4-40 Ball Links for connecting rudder servo
(4) 4-40x16mm hex head bolts for connecting rudder
servo
(4) 4-40x20mm hex head bolts for connecting rudder
servo
(4) Brass Spacers for connecting rudder servo
(4) 3mm flat washers for connecting rudder servo
(4) 4-40 Ball Links – Rudder
(4) 4-40 x16mm hex style bolts
(6) 4-40 lock nuts
(2) Brass Spacers for rudder
(2)
Φ
3 flat washers
#8:
(1) 1000cc Gas Fuel Tank Assembly
(1) 750cc Gas Fuel Tank Assembly
(1) 4ft. large gas fuel line
(4) Brass Barbs for fuel line
(2) Fuel filler Dot – 1 male and 1 female
#9:
(2)Throttle and Choke servo mounting trays
(1) Canister mounting bracket with Silicon Tubes
(3) Engine Mounting Template (DA100;3W100 and
Universal)
(2) 8x8x300mm Sponge for the receiver and battery
(1) 6x70x160mm Foam for the Fuel Tank
