Aerotech XC2e Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 92

Aerotech XC2e Скачать руководство пользователя страница 13

Safety Procedures and Warnings

IMPORTANT

: This manual tells you how to carefully and correctly use and operate the

XC2e.

l

Read all parts of this manual before you install or operate the XC2e or before you do
maintenance to your system.

l

To prevent injury to you and damage to the equipment, obey the precautions in this
manual.

l

All specifications and illustrations are for reference only and were complete and
accurate as of the release of this manual. To find the newest information about this
product, refer to www.aerotech.com.

If you do not understand the information in this manual, contact AerotechGlobal Technical
Support

WARNING

: This product has been designed for light industrial manufacturing or

laboratory environments. The protection provided by the equipment could be impaired if
the product is used in a manner not specified by the manufacturer.

DANGER

: The voltage from this product can kill you. To decrease the risk of electrical

shock, injury, and death, you must obey the precautions that follow.

1. Before you do maintenance to the equipment, disconnect the electrical power.
2. Wait at least one (1) minute after removing the power supply before doing main-

tenance or an inspection. Otherwise, there is the danger of electric shock.

3. Before you connect wires to this product, disconnect the electrical power.
4. To decrease the risk of electrical shock and injury, you must supply operators with

the necessary precautions and protection from live electrical circuits.

5. While the drive is connected to a power source, do not connect or disconnect elec-

trical components and cables.

6. Make sure that all components are grounded correctly and that they obey the local

electrical safety requirements.

7. Make sure that you install the necessary precautions to supply safety and pro-

tection to the operator.

8. Moving parts can cause crushing or shearing injuries. You must limit access to all

motor and stage parts while your system is connected to a power source.

WARNING

: To prevent damage to the equipment and decrease the risk of electrical shock,

injury, and death, you must obey the precautions that follow.

1. Make sure that all system cables are correctly attached and positioned.
2. Use this product only in environments and operating conditions that are approved

in this manual.

3. Only operators who have received training can operate this equipment. All servicing

and maintenance must be done only by approved personnel.

www.aerotech.com

13

XC2e Hardware Manual

Safety Procedures and Warnings

«
...
11
12
13
14
15
...
»

Содержание XC2e





























































































Отзывы:

Нет отзывов