manualshive.com logo in svg

Aerotech Ensemble HLe, Руководство по оборудованию, Страница: 36 / 112

Поделиться
Скачать
Aerotech Ensemble HLe Скачать руководство пользователя страница 36

36

Chapter 2

www.aerotech.com

2.3.1. Encoder Interface (J207)

The Ensemble HLe is equipped with standard and auxiliary encoder feedback channels. The standard
encoder interface is accessible through the Motor Feedback (J207) connector. The standard encoder
interface will accept an RS-422 differential line driver signal. If the Ensemble HLe has been purchased with
the -MXH option, the standard encoder interface can be configured for an analog encoder input via parameter
settings.

Refer to

Section 2.3.1.4.

for encoder feedback phasing. Refer to

Section 2.5.

for the auxiliary encoder

channel.

N O T E :

 Encoder wiring should be physically isolated from motor, AC power, and all other power wiring.

Table 2-11:

Encoder Pins on the Motor Feedback Connector

Pin#

Description

In/Out/Bi

1

Chassis Frame Ground

N/A

3

+5V Power for Encoder (500 mA max)

Output

6

Encoder Marker Reference Pulse -

Input

Absolute Encoder Interface Clock -

Output

7

Encoder Marker Reference Pulse +

Input

Absolute Encoder Interface Clock +

Output

14

Encoder 

Input

15

Encoder Cosine -

Input

17

Encoder Sine +

Input

18

Encoder Sine -

Input

21

Signal Common for Encoder

N/A

Ensemble HLe

Installation and Configuration

Содержание Ensemble HLe

















































































































Отзывы:

Нет отзывов