Aerotech Ensemble HLe Скачать руководство пользователя страница 106 | Manualshive

Страница: 106 / 112

background image

106

Appendix A

www.aerotech.com

Rush Service

At times, the buyer may desire to expedite a repair. Regardless of warranty or out-of-warranty status, the
buyer must issue a valid purchase order to cover the added rush service cost. Rush service is subject to
Aerotech's approval.

On-site Warranty Repair

If an Aerotech product cannot be made functional by telephone assistance or by sending and having the
customer install replacement parts, and cannot be returned to the Aerotech service center for repair, and if
Aerotech determines the problem could be warranty-related, then the following policy applies:

Aerotech will provide an on-site Field Service Representative in a reasonable amount of time, provided
that the customer issues a valid purchase order to Aerotech covering all transportation and subsistence
costs. For warranty field repairs, the customer will not be charged for the cost of labor and material. If
service is rendered at times other than normal work periods, then special rates apply.

If during the on-site repair it is determined the problem is not warranty related, then the terms and
conditions stated in the following “On-Site Non-Warranty Repair” section apply.

On-site Non-Warranty Repair

If any Aerotech product cannot be made functional by telephone assistance or purchased replacement parts,
and cannot be returned to the Aerotech service center for repair, then the following field service policy
applies:

Aerotech will provide an on-site Field Service Representative in a reasonable amount of time, provided
that the customer issues a valid purchase order to Aerotech covering all transportation and subsistence
costs and the prevailing labor cost, including travel time, necessary to complete the repair.

Service Locations

http://www.aerotech.com/contact-sales.aspx?mapState=showMap

USA, CANADA, MEXICO

CHINA

GERMANY

Aerotech, Inc.

Aerotech China

Aerotech Germany

Global Headquarters

Full-Service Subsidiary

Full-Service Subsidiary

Phone: +1-412-967-6440

Phone: +86 (21) 5508 6731

Phone: +49 (0)911 967 9370

Fax: +1-412-967-6870

Fax: +49 (0)911 967 93720

JAPAN

TAIWAN

UNITED KINGDOM

Aerotech Japan

Aerotech Taiwan

Aerotech United Kingdom

Full-Service Subsidiary

Full-Service Subsidiary

Full-Service Subsidiary

Phone: +81 (0)50 5830 6814

Phone: +886 (0)2 8751 6690

Phone: +44 (0)1256 855055

Fax: +81 (0)43 306 3773

Fax: +44 (0)1256 855649

Have your customer order number ready before calling.

Ensemble HLe

Warranty and Field Service

«
...
104
105
106
107
108
...
»

Содержание Ensemble HLe

















































































































Отзывы:

Нет отзывов

Похожие инструкции для Ensemble HLe

Бренд: NCR Страницы: 6

Бренд: Aalborg Страницы: 128

Бренд: ABB Страницы: 63

Бренд: rada Страницы: 16

Бренд: RADEMACHER Страницы: 48

Бренд: Saab Страницы: 4

Бренд: C&C Страницы: 17

Бренд: OJ Electronics Страницы: 8

Бренд: tell Страницы: 11

AQUASNAP 30RA "B"

Бренд: Carrier Страницы: 36

Freedom Bridge FB3

Бренд: Identiv Страницы: 2

IntelliCross TouchFree Kit

Бренд: Novax Страницы: 3

Бренд: Daikin Страницы: 19

Бренд: HEROSE Страницы: 92

Бренд: Argo-Hytos Страницы: 38

Бренд: Anest Iwata Страницы: 8

M-DUINO PLUS series

Бренд: Industrial Shields Страницы: 46

Бренд: Gateway Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды