Aerotech BL 10-40 Скачать руководство пользователя страница 24

Страница: 24 / 68

Installation and Configuration

2.5. Potentiometers (POTs)

Potentiometers INPUT, TACH, GAIN, and BAL (balance) are associated with the pre amplifier circuit con-

tained in the amplifier. These potentiometers are used to adjust the pre-amplifier gain when the MODE

switch is set for velocity control using an external DC tachometer or incremental encoder for velocity feed-

back.

Table 2-7:

Potentiometer Functions

Potentiometer

CCW

Function

INPUT

Increase

Decrease This pot adjusts the DC gain of the input com-

mand present at J101 Pins 8 & 21.

TACH

Increase

Decrease This pot adjusts the DC gain of the tach or

encoder derived velocity feedback input present

at J101-Pin 3.

GAIN

Decrease

Increase

This pot adjusts the AC gain of the pre-amplifier.

BAL

Provides the means of canceling small DC off-

sets that may be present in the pre amplifier cir-

cuit.

This figure illustrates a portion of the pre-amplifier circuit that is accessible to the user for adjusting com-

mand signal gains.

Figure 2-3:

Command Signal Adjustment of the Pre-Amplifier Circuit

Chapter 2

www.aerotech.com

Содержание BL 10-40





































































Результаты поиска

Содержание BL 10-40

Отзывы:

Похожие инструкции для BL 10-40

Бренды по названию

Популярные бренды

Aerotech BL 10-40, Руководство по оборудованию

Результаты поиска

Содержание BL 10-40

Отзывы:

Похожие инструкции для BL 10-40

Бренды по названию

Популярные бренды