manualshive.com logo in svg

Aerotech ANT130L Series, Руководство по оборудованию

Поделиться
Скачать
Aerotech ANT130L Series Скачать руководство пользователя страница 14

Each stage  has a label listing the system part number and serial number. These numbers contain
information necessary for maintenance or system hardware and software updates. Locate this label
and record the information for later reference.

Red, anodized aluminum shipping brackets have been installed to prevent unwanted motion
damage that could occur during shipment. The brackets must be removed before the ANT130L can
be operated. Retain the brackets and hardware for future use.

DANGER: Mechanical Hazard!

l

The product can move manually without electrical power connected.

l

When the shipping brackets are removed, the operator could be exposed to pinch
points.

Figure 3:

Shipping Brackets

Storage

Store the stage in the original shipping container. If the original packaging included ESD protective
packaging, make sure to store the stage in it. The storage location must be dry, free of dust, free of
vibrations, and flat.

Refer to

Section 1.1. Environmental Specifications

Handling and Storage

ANT130L Hardware Manual

14

www.aerotech.com

Содержание ANT130L Series

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды