Angle Finish Nailer DA64R Http://www.aeroprotools.com
3
The characteris
�c
vibra
�
on values for the fastener driving tool have been determined in accordance with ISO 8662-11:1999 and EN
12096 ¨C Measurement of vibra
�
on in hand-held power tools - Part 11: Fastener driving tools(see speci
fica�
ons).
This value is a tool-related characteris
�
c value and does not represent the in
fl
uence to the hand-arm-system when using the tool. An
in
fl
uence to the hand-arm-system when using the tool will for example depend on the gripping force, the contact pressure force, the
working dire
c�
on, the adjustment of compressed air supply, the workplace and the work piece support.
ADDITIONAL SAFETY INSTRUCTIONS FOR PNEUMATIC POWER TOOLS
Air under pressure can cause severe injury.
Always shut o
ff
air supply, drain hose of air pressure and disconnect tool from air supply whenever not in use, before changing
accessories or where making repairs.
Never direct air at yourself or anyone else.
Whipping hoses can cause severe injury. Always check for damaged or loose hoses and
fi�
ngs.
Cold air should be directed away from the hands.
Whenever universal twist couplings(claw couplings) are used, lock pins shall be installed and whip check safety cables shall be used
to safeguard against possible hose-to-tool and hose-to-hose conne
c�o
n failure.
Do not exceed the maximum air pressure stated on the tool.
Never carry an air tool by the hose.
Only fasteners listed in the speci
fi
ca
�o
ns may be used in the fastener driving tool. The fastener driving tool and the fasteners
speci
fi
ed in the speci
fi
ca
�o
ns are to be considered as one unit safety system.
Quick ac
�o
n couplings shall be used for conne
c�
on to the compressed air system and the non-sealable nipple must be
fi�
ed at the
tool in such a way that no compressed air remains in the tool a
�er
disconnec
�o
n.
Oxygen or combus
�
ble gases shall not be used as an energy source for compressed air operated fastener driving tools.
Fastener driving tools shall only be connected to an air supply where the maximum allowable pressure of the tool cannot be
exceeded by more than 10%; in the case of higher pressure ,a pressure reducing valve which includes a downstream safety valve
shall be built into the compressed air supply.
Only the main energy and the lubricants listed in the opera
�
ng instru
c�
ons may be used for the maintenance of fastener driving
tools. Only spare parts speci
fi
ed by the manufacturer or his authorised representa
�
ve shall be used.
Repairs shall be carried out only by the manufacturer's authorized agents or by other experts, having due regard to the
informa
�o
n given in the opera
�
ng instru
c�
ons.
Stands for moun
�
ng the fastener driving tools to a support, for example to a work table, shall be designed and constructed by the
stand manufacturer in such a way that the fastener driving tools can be safely
fix
ed for the intended use, thus for example
avoiding damage, disto
r�
on and displacement.
Check prior to each opera
�
on that the safety and triggering mechanism is fun
c�
oning properly and that all nuts and bolts are right.
Do not carry out any a
ltera�
ons to the fastener driving tool.
Do not disassemble or make inopera
�
ve any parts of the fastener driving tool such as the safety yoke.
Do not perform any ¡°emergency repairs¡± without proper tools and equipment.
The fastener driving tool should be serviced properly and at regular intervals in accordance with the manufacturer¡¯s instru
c�
ons.
Avoid weakening or damaging the tool, for example by:
-punching or engraving;
-modi
fica�
on not authorized by the manufacturer;
-guiding against templates made of hard material such as steel;
-dropping or pushing across the
flo
or;
-using the tool as a hammer;
-applying excessive force of any kind.
Never point any fastener driving tool at yourself or at any other person or animal.
Hold the fastener driving tool during the work opera
�
on in such a way that no injuries can be caused to the head or to the body in
the event of possible recoil consequent upon a disrup
�
on in the compressed air supply or hard areas within the workplace.
Never actuate the fastener driving tool into free space. This will avoid any hazard caused by free
flyi
ng fasteners and excessive
strain of the tool.
The tool shall be disconnected from the compressed air system for the purpose of transporta
�
on, especially where ladders are
used or where an unusual physical posture is adopted whilst moving .
Carry the fastener driving tool at the workplace using only the handle, and never with the trigger actuated.
Take cond
i�
ons at the workplace into account. Fasteners can penetrate thin work pieces or slip o
ff
corners and edges of
workplaces, and thus put people at risk.
For personal safety, use prote
c�
ve equipment such ad hearing and eye pro
tec�o
n.
Fastener driving tools are operated by actua
�
ng the trigger using
fi
nger pressure.