background image

 

                                                                                                                       

Xenon 

 
Xenon building instructions 

 

 

ways best to use approved model flying sites. 

 

Never fly towards or over spectators. Keep any high-risk flying manoeuvres well away from other 
people. 

 

Never  attempt  to  repair  your  radio  control  system;  always  leave  such  work  to  the  experts.  Any 
home modifications to your RC system inevitably invalidate its official approval. 

 

Do not switch your transmitter on until and unless you have ensured that you will not cause inter-
ference to any other radio control systems in the vicinity; typically through a “channel clash” (two 
transmitters on the same frequency). 

 

If  possible,  join  a  model  flying  club,  where  you  will  find  plenty  of  friendly  people  to  help  with  all 
your queries and problems. 

 

Please  note:  if  damage  ensues  due  to  failure  to  observe  these  instructions,  the  guarantee  is 
rendered  invalid.  We  accept  no  liability  for  consequent  damage  which  results  from  such  ac-
tions. Please follow the building instructions to the letter when completing and operating this 
model. The building instructions include information on safe flying. This model is in no respect 
a children’s toy. 

 
 

All of us in the aero-naut Modellbau team hope you have many hours of fun 

with your “Xenon”! 

 
 
 

aero-naut Modellbau GmbH & Co KG, Stuttgarter Strasse 18-22, 72766 Reutlingen, www.aero-naut.com 

 
 

Содержание Xenon RC







Отзывы: