Aero HygenX 34541 PCPA Скачать руководство пользователя | Manualshive

Страница: 17 / 23

background image

17

f. Slide the connector and lamp back down into

the black UVC holder.

CLEANING

a. Clean

Aero HygenX RAY – Autonomous UVC Robot

with a soft, dry cloth.

b. For more stubborn stains, use a soft cloth slightly dampened with a solution of mild

soap and warm water. Do not use alcohol or acetone-based cleaners.

c. Do not allow water or other liquids to pool or enter the unit from the top panel.

d. Ensure the inside electronic components are not exposed to water or moisture.

«
...
15
16
17
18
19
...
»

Содержание 34541 PCPA
























Отзывы:

Нет отзывов

Похожие инструкции для 34541 PCPA

Бренд: JAKA Страницы: 80

Бренд: Asus Страницы: 13

Recon Scout OCU02

Бренд: ReconRobotics Страницы: 12

Ultimate Initio kit

Бренд: 4tronix Страницы: 11

Бренд: ABB Страницы: 660

Бренд: ABB Страницы: 720

OmniCore V400XT

Бренд: ABB Страницы: 466

Бренд: SAKE ROBOTICS Страницы: 5

Бренд: Shini Страницы: 49

Бренд: REV Страницы: 56

Бренд: YZ Robot Страницы: 14

Бренд: Hitbot Страницы: 9

Бренд: Vex Robotics Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды