39
E
nglish
1508 - 5138800_00
The programme requires the system to circulate chilled water.
ϭΉWZ^^d,KEͬK&&
OR
<z^
The fan coil unit comes on. The fan coil unit automatically starts in cooling mode.
ϮΉWZ^^d,DK<z
Press the MODE key repeatedly until the word COOL appears on the display (TLW2) or
the LEDs on wired control panel (PFW2) turns on COOL.
ϯΉWZ^^d,<z^
OR
dKKEdZK>d,dDWZdhZ
– The key with the symbol
allows increases of 1°C
– The key with the symbol
allows decreases of 1°C
The display shows the set point value between 16 and 30 °C.
ϰΉWZ^^d,&E<z
OR
When the FAN key is pressed repeatedly, the system can move to the minimum speed
(LOW), medium speed (MED) and high speed (HIGH) or to the (AUTO) speed controlled
by the microprocessor.
ϱΉdK/Zdd,/Z&>Kt
To ensure optimum air distribution, adjust the horizontal blades and the vertical blades
in such a way that the air flow does not hit people directly. The vertical air flow blades
must be set manually before starting up the motorised blades.
Never adjust the motorised horizontal blades manually.
When the LOUVER key is pressed repeatedly, the horizontal blade is adjusted to 4 fixed
blade positions, then a swinging blade movement will begin. If you wish to stop the
blade in a particular position, press the LOUVER key.
When the SWING
key is pressed a swinging blade movement will begin. If you wish to
stop the blade in a particular position, press the
SWING key again.
ϲΉWZ^^d,^E<zΈd>tϮΉ
To transmit the new parameters shown on the LCD to the main control unit.
6
PFW2
TLW2
ϭΉWZ^^d,KEͬK&&
OR
<z^
The fan coil comes on and the display is switched on.
ϮΉWZ^^d,DK<z
Press the MODE key repeatedly until the word FUN appears on the display (TLW2) or
the LEDs on wired control panel (PFW2) turns on FUN.
ϯΉWZ^^d,&E
OR
<z^
When the FAN key is pressed repeatedly, the system can move to the minimum speed
(LOW), medium speed (MED) and high speed (HIGH) or to the (AUTO) speed controlled
by the microprocessor.
ϰΉdK/Zdd,/Z&>Kt
To ensure optimum air distribution, adjust the horizontal blades and the vertical
blades in such a way that the air flow does not hit people directly. The vertical air flow
blades must be set manually before starting up the motorised blades.
Never adjust the motorised horizontal blades manually.
When the LOUVER key is pressed repeatedly, the horizontal blade is adjusted to 4 fixed
blade positions, then a swinging blade movement will begin. If you wish to stop the
blade in a particular position, press the LOUVER key.
When the SWING
key is pressed a swinging blade movement will begin. If you wish to
stop the blade in a particular position, press the
SWING key again.
ϱΉWZ^^d,^E<zΈd>tϮΉ
To transmit the new parameters shown on the LCD to the main control unit.
KWZd/E'/E:h^dsEd/>d/KEDK
This programme is used to move the room air and avoid stagnation. The ventilation
programme is particularly indicated as a support to heating systems without fans, as
when a stove is used to heat the room. All the hot air gathers by the ceiling. When
the unit is set in ventilation mode, the hot air is distributed uniformly throughout the
room.
PFW2
TLW2
KK>/E'WZK'ZDDΈKK>Ή
&EWZK'ZDDΈ&EΉ
