background image

Mits Airconditioning Inc

Master Distributor in North America

for Aermec S.P.A.

Limited Warranty Information and Registration

This warranty is extended by Mits Airconditioning Inc (hereafter referred to as MITS) to the final

purchaser. MITS warrants it’s products to be free of defects in materials and workmanship at
the time of original purchase and for subsequent periods of time as described below.

Aermec Chiller and Heat Pumps parts are warranted to be free from manufacturing defects for
up to 12 months from the date of installation.

The compressor is warranted for 5 years from the date of installation for residential
application and 1 year for commercial applications.

Aermec Fan Coil parts are warranted to be free from manufacturing defects up to 12 months
from date of installation.

Aermec Accessories – valves, storage tank, expansion tank, and control are warranted to be
free from defects for up to 12 months from the date of original installation.

If, during the period of warranty, the products listed prove defective under normal use and
service due to improper materials or workmanship as determined by MITS, the company will at
its sole discretion replace the defective part or component.

Conditions:

In the event MITS replaces a part or component, the repaired or replaced product shall
be warranted under the original limited warranty for the remainder of the original
warranty period.

The warranty does not cover any failure of components not supplied by MITS, nor does
it cover failure of any part due to misuse (including neglect, improper installation, repair
alteration, modification, or adjustment).

Damage caused by freezing, corrosion, and fouling is not covered under this warranty.

There are no other express warranties, whether written or oral other than this printed
limited warranty. All implied warranties, including without limitation the implied
warranties or merchantability or fitness for a particular purpose, are limited to the
duration of this limited warranty. In no way shall the company be liable for incidental or
consequential damages of any nature whatsoever, including but not limited to lost
profits or commercial loss, to the full extent those damages can be disclaimed by law.

1608 Bonhill Road, Mississauga, On, L5T 1C7

Toll Free: 1-800-567-2221(Canada)

Toll Free: 1-888-567-2227 (USA)

www.aermec.ca

www.aermec.us

Содержание ANK















Отзывы: