background image

4

www.aerex.de

Reco-Boxx ZXR / ZXA / Flat – Operation and maintenance instructions 

[03/

2021]

2.0  Basic safety instructions

 

2.1 Intended use

This ventilation unit with heat recovery is used in 
centralised or decentralised ventilation systems. 
The unit provides controlled ventilation and air 
extraction in, for example, offices, school class-
rooms and other similar spaces. The units are 
intended for ceiling-mounted installation because 
they have outside air/outgoing air sockets on 
the sides and/or discharging upwards. Please 
note that the unit is very heavy, weighing approx. 
210 kg. The unit may only be used if installed 
permanently, in dry indoor spaces and with 
connected ventilation ducts. DN 250 connection 
for geniovent.x 600 H and DN 315 connection 
for geniovent.x 900 H. The units do not have unit 
switches. Scope for completely disconnecting 
the unit from the power supply should be pro-
vided by the customer. These ventilation units 
are only intended for domestic use and similar 
purposes. No other or additional use is intended.

 

2.2  Specialist installer qualifications

The ventilation unit may only be installed, set up, 
retrofitted, started up, cleaned and maintained 
by a trained specialist in accordance with these 
instructions. You are deemed a trained spe-
cialist if your education, training or experience 
in ventilation technology mean that you can 
competently and safely undertake installation in 
accordance with the planning requirements and 
these instructions and are able to recognise and 
avoid risks resulting from incorrect installations 
and settings and the dangers resulting from 
them. Only a qualified electrician is permitted to 
work on the electrics. You are deemed a qualified 
electrician if you are familiar with the relevant 
standards and guidelines, can competently and 
safely create electrical connections in line with 
the attached wiring diagram and are able to 
recognise and avoid risks and dangers associat-
ed with electricity on the basis of your technical 
training and experience. Repair work may only be 
undertaken by an authorised AEREX specialist. 
After successful installation and commissioning, 
instruct users in the ventilation unit and associat-
ed control unit.

 

2.3  Non-intended use

The ventilation unit must not be used in the fol-
lowing situations under any circumstances. Read 
all the safety instructions.

Risk of combustion/fire from flammable ma-
terials, liquids or gases in the vicinity of the 
ventilation unit.

 Do not place any flammable ma-

terials, liquids or gases near the ventilation unit, 
which may ignite in the event of heat or sparks 
and catch fire.

Risk of death if an air-ventilated fireplace is  
connected to an exhaust gas system, which 
itself has multiple connections

. The air-venti-

lated fireplace may result in exhaust fumes being 
transferred to other living units. Risk of death, for 
example from carbon monoxide. Never use the 
ventilation unit if there are air-ventilated fireplaces 
in the living unit that are connected to exhaust 
gas systems, which themselves have multiple 
connections.

Explosion hazard.

 Explosive gases and dust 

may ignite and cause serious explosions or fire.  
 Never use ventilation unit in an explosive atmos-
phere.

Explosion hazard.

 Explosive substances in lab 

extraction units may ignite and cause serious 
explosions or fire. Aggressive substances may 
damage the ventilation unit. Never use ventilation 
unit in combination with a lab extraction unit.

Risk to health from chemicals or aggressive 
gases/vapours.

 Chemicals or aggressive gases/

vapours may present a risk to health, especially 
if the ventilation unit distributes them into rooms. 
Never use the ventilation unit to convey chemi-
cals or aggressive gases/vapours.

Damage to the unit. 

•  If operated during the build phase, potential 

damage to unit caused by contamination of 
the ventilation unit and ventilation ducts. Venti-
lation unit operation is not permitted during the 
build phase

•  Grease and oil vapours from range hoods may 

contaminate the unit and ventilation ducts 
and reduce efficiency. Never use ventilation 
unit in combination with range hoods, that are 
connected directly to the controlled domestic 
ventilation exhaust air channel. In rooms with 

Содержание 0040.0420

























































Отзывы: