manualshive.com logo in svg

Aereco DXR 230 REFERENCE, Инструкция по установке и обслуживанию

Поделиться
Скачать
Aereco DXR 230 REFERENCE Скачать руководство пользователя страница 15

 

15 / 36

TF6775_A_NOT_DXR230_REFERENCE 

Aereco S.A.

230 VAC

D

E

230 VAC

in

out

RJ45

Modbus RJ45 cable

Smart interface

A

B

C

D6688_A

Wi-Fi ON

4

 - Modbus connection

5

 - Modbus connection

6

 - Ethernet

7

 - Power ON

8

 - Modbus ON

9

 - Modbus traffic

bus cap

bus cap

DXR unit

RJ45 cable

4. 

ELECTRICAL CONNECTIONS

Disconnect the electrical supply before any operations and ensure that the DXR Unit 

cannot be started accidentally.

Only cables provided by Aereco must be used to carry on the DXR Unit installation. If using 

different cables, Aereco won’t be able to guarantee the good functioning of the appliance.

The installation must be carried out by a professional 

in compliance with applicable 

regulations in force in the country of installation. Each product or component used in the 
installation must also comply with standards in force in the country.

ModBus components (2I2O module or 

smart interface) may be connected on 

one of the 2 RJ45 ModBus socket (the one 

you want, it doesn't matter) for a parallel 

wiring. But the ModBus components may 

also be connected one after the other for a 

serial wiring, up to you.

Each modbus line must be ended with a 
ModBus cap. So, 2 ModBus caps must be 
connected on the ModBus network (because 2 
RJ45 ModBus sockets on the main electronic 
board).

A

DXR Unit

B

Smart interface

C

2I2O module

D

Defrosting

E

Lift pump

RJ 45

Supply (230 V): 1.5 mm².

Note: RJ45 cables provide both supply and connections.

RJ45 maximal length: loop = 100m

D6688_A

Wi-Fi ON

4

 - Modbus connection

5

 - Modbus connection

6

 - Ethernet

7

 - Power ON

8

 - Modbus ON

9

 - Modbus traffic

bus cap

Modbus

RJ45

Modbus RJ45

Parallel wiring 

bus cap

2I2O

Smart interface

DXR unit

Serial wiring 

Modbus

cap

2I2O

Smart interface

Note: It's possible to connect the smart interface and the 2I2O module with a parallel or a serial wiring.

Содержание DXR 230 REFERENCE





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды