Aereco DXR 230 REFERENCE страница 23 Скачать руководство пользователя | Manualshive

Страница: 23 / 36

background image

23 / 36

TF6775_A_NOT_DXR230_REFERENCE

Aereco S.A.

6.3. FILTERS

The interface indicates when the filters need to be changed. Their change is easily realised through
the two access hatches (no tool needed).

The bottom cover of the DXR Unit must not be dismounted for this operation. All filters

(1xG4 and 1xF7) must be replaced at the same time.

Filter removal/replacement:

Removal

2. Remove both filter hatches
Remove 2 fixing buttons. Hold the hatches with you hand to prevent it from falling.

3. Remove each filter by holding it firmly along its edge and pulling it downward out of the filter slot
(the filter is a push-fit item and not fastened in place).

1. Switch off the unit.

Fresh air

(outdoor)

G4 filter

Exhaust air

(indoor)

F7 filter

«
...
21
22
23
24
25
...
»

Содержание DXR 230 REFERENCE





































Отзывы:

Нет отзывов

Похожие инструкции для DXR 230 REFERENCE

Бренд: EasyPro Страницы: 8

Бренд: Easylift Страницы: 127

Бренд: Abicor Binzel Страницы: 42

GYRO TECH GT-1175

Бренд: Nabco Страницы: 31

GYRO TECH GT-1175

Бренд: Nabco Страницы: 33

Бренд: Q-See Страницы: 141

Бренд: Panasonic Страницы: 1

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 20

Бренд: ABICOR Страницы: 16

KegMaster 4 Series

Бренд: Keg King Страницы: 17

Бренд: Karaoke USA Страницы: 32

Бренд: R-Tech Страницы: 19

Бренд: Turbosound Страницы: 13

Бренд: Olympia Страницы: 40

Бренд: Lincoln Electric Страницы: 15

Бренд: YOKOGAWA Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды